Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Oct 31, 2024 6:21 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 33 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Neck block for bolt on
PostPosted: Mon Nov 08, 2021 9:44 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1544
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
I've gone through all my stock and have nothing large enough for the neck block according to the plan. Since this is going to be a bolt on, I'm thinking it's not a big deal to glue up something. The sapele I have is thick enough but not tall enough so I glued extra material on. I'll keep the joint below the bolt holes and I think it will be fine. I also think this would be a good place for plywood and I may go that route someday. I'm not trying to sell anything so until that day I'm not concerned with tradition.

BTW, I have a ton of mahogany-ish wood to devote to this and hate to throw it in the fire.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 9:56 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3384
Location: Alexandria MN
Hibdon Hardwood sells head and tail block material at reasonable prices. That is where I have been getting mine recently.

https://www.hibdonhardwood.com/collecti ... end-blocks

_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 10:21 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1544
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
If shipping was free I might consider it, probably not. As I said, I have plenty of this stuff on hand, but I'll look.

I just checked shipping, $25 for 2 blocks, that aint gonna happen.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 10:42 am 
Offline
Koa
Koa

Joined: Mon Oct 17, 2011 4:10 pm
Posts: 713
First name: Bob
Last Name: Gramann
City: Fredericksburg
State: VA
Zip/Postal Code: 22408
Country: USA
Focus: Build
Status: Professional
I’ve glued up one as you describe and it worked fine. Usually, I cut the headblock out of (and in the same orientation of) the neck wood. I rotate the block so that I’m gluing to and bolting through side grain. If anything moves, I want the headblock and the neck to move together so the fingerboard isn’t distorted at the body/neck joint.

I usually buy 12/4 planks for my neck wood. This yields 3” wide quartersawn blanks. I cut the blocks out of the same lumber.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 11:42 am 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
I personally think a laminated neck block is superior in strength and is also easier to come by. Folks stack heels all the time, so why not a neck block? Funny, I use a solid block for my heel…

Best, M


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 12:25 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1544
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
That block looks like a lot of work. I'm in, show me how :-)

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!



These users thanked the author banjopicks for the post: Michaeldc (Mon Nov 08, 2021 12:54 pm)
Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 12:36 pm 
Offline
Koa
Koa

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 1030
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur
What a beautiful neck block! I use a vaguely similar fingerboard attachment too (Luthier's Cool Tools, Dave Micheletti).

_________________
Peter Havriluk



These users thanked the author phavriluk for the post: Michaeldc (Mon Nov 08, 2021 12:54 pm)
Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 12:52 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
banjopicks wrote:
That block looks like a lot of work. I'm in, show me how :-)


Yeah, it’s largely cut CNC.

I’m sure you could do it with a half a dozen templates and a pair of fixtures to hold the block during. I’ve likely got a PDF I could email if you want to give it a go. I’d have to find it and I’d need you to pm your email.

The block fits every model I build from my “0” through my 28” baritone fan-fret. I make a dozen blocks at a time so I just grab a block off the shelf, radius the head and trim the extension to length.

M


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 12:57 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1544
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
Thanks, I'll figure it out. Looks like a fun hand tool assignment.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 12:59 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
banjopicks wrote:
Thanks, I'll figure it out. Looks like a fun hand tool assignment.


You’re more patient than me -

Good luck with it!


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 2:23 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jul 10, 2009 4:44 am
Posts: 5484
First name: colin
Last Name: north
Country: Scotland.
Focus: Build
Status: Semi-pro
I do similar but glue the FB extension.
My UTB is wedged against the neck block "protuberance"

_________________
The name catgut is confusing. There are two explanations for the mix up.

Catgut is an abbreviation of the word cattle gut. Gut strings are made from sheep or goat intestines, in the past even from horse, mule or donkey intestines.

Otherwise it could be from the word kitgut or kitstring. Kit meant fiddle, not kitten.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 2:34 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sun Mar 30, 2008 8:20 am
Posts: 5967
I do plywood/mahogany glued up end blocks for bolt on necks. Sometimes it's two layers of Baltic birch and a 1/2 inch thick piece of mahogany and sometimes a single thickness of BB and a 3/4 inch piece of mahogany. I veneer the edges with mahogany veneer and usually chamfer or round the face. I usually make up a longer piece of end block stock and then cut to the length I need for the particular instrument. It is a good way to use those odd pieces of wood that is too thick for one thing and too thin for another.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 2:51 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jan 22, 2010 9:59 pm
Posts: 3590
First name: Dennis
Last Name: Kincheloe
City: Kansas City
State: MO
Country: USA
Focus: Build
Status: Amateur
The only time I'd worry about glue in a neck block is when steaming apart a dovetail.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 3:02 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
DennisK wrote:
The only time I'd worry about glue in a neck block is when steaming apart a dovetail.


Good point!


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 3:07 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1544
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
Michael, I'm looking at the shallow groove on top of the extension. Is that for partial popsicle brace?

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 3:32 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
banjopicks wrote:
Michael, I'm looking at the shallow groove on top of the extension. Is that for partial popsicle brace?


It is,

It goes in before the top goes on and is trimmed after using a bottom bearing, 1/4” flush-cut bit. You can see it after trimming in the left corner of the pocket.

M


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 3:42 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
Colin North wrote:
I do similar but glue the FB extension.
My UTB is wedged against the neck block "protuberance"


I do the same, except the UTB is glued to the extension block and the linings prior to the top going on. It helps hold the geometry where I want it.

Best, M


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 5:01 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6983
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
West Penn Hardwoods, used to advertise here. I order 4x4 and 8x4 mahogany boards for this stuff. Min order goes a long way.


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 7:30 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7369
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
Do you make your own linings Michael?


Top
 Profile  
 
PostPosted: Mon Nov 08, 2021 8:12 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
meddlingfool wrote:
Do you make your own linings Michael?


Yes



These users thanked the author Michaeldc for the post: meddlingfool (Tue Nov 09, 2021 12:02 pm)
Top
 Profile  
 
PostPosted: Tue Nov 09, 2021 4:52 am 
Offline
Koa
Koa

Joined: Tue Jan 15, 2013 10:00 pm
Posts: 985
First name: Josh
Focus: Build
Status: Amateur
Similar to Michael, Colin and others, I glue my neck blocks up from two pieces. This helps me use up off cuts from neck blanks etc that would otherwise go in the burn pile. I’m a big fan of the stiffening effect from having the long ‘head block extension’ glued up to the UTB, and having a very strong structure under the fb extension. I glue the fb extension down, rather than bolt it.

Image


Top
 Profile  
 
PostPosted: Tue Nov 09, 2021 6:12 am 
Offline
Koa
Koa
User avatar

Joined: Sat Jan 19, 2013 7:33 am
Posts: 1874
First name: Willard
Last Name: Guthrie
City: Cumberland
State: Maryland 21502
Zip/Postal Code: 21502
Country: United State
Focus: Repair
Status: Semi-pro
Has anyone seen any real evidence that a neck block extension supporting the top - versus the slipper foot, which seems like it actually provides some resistance to back flattening - does anything useful in resisting the body distortion that eventually leads to the necessity of a neck reset?

Having seen enough Martins with the neck block extensions versus those without coming in for work, it seems like time between neck resets has decreased with the extensions, rather than increased. I know their extensions are not physically tied into the UTB, but I would have thought that any extension supporting the top would have been helpful.

_________________
If you're really successful at (BS'ing), it means you're not hanging around enough people smarter than you.

Neil deGrasse Tyson


Top
 Profile  
 
PostPosted: Tue Nov 09, 2021 8:06 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Dec 17, 2013 10:52 pm
Posts: 3059
First name: Don
Last Name: Parker
City: Charleston
State: West Virginia
Zip/Postal Code: 25314
Country: USA
Focus: Build
Status: Amateur
I figure that body distortion is not limited to the areas above the UTB, so corrective measures above the UTB can’t solve all body distortion problems. Changing things between the head block and the UTB can help (or make things worse) regarding related problems, like top cracks along the edge of the fingerboard extension. But tops will bulge, sides will shift, backs will flatten, etc., regardless of what we do in that little space under the fingerboard extension. I’m currently using a variation of the trapezoidal patch John Arnold has mentioned here on the OLF. It makes a lot of sense to me.


Top
 Profile  
 
PostPosted: Tue Nov 09, 2021 9:02 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1544
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
I've been thinking about gluing procedures for blocks. I believe the neck block should be flat and I'm not so sure my mold is perfectly flat in that area. My thought is to glue the block and clamp as much as I can so I don't change the shape of the sides as I have them pre-shaped to plan. Then open the mold, I need to make arrangements for that prior to doing it. I need to add a locater dowel and a way to add clamps to hold it together instead of screws. Then I feel confident to glue the block in and remove it from the mold and add more clamps. This way I can maintain my center lines and pre-cut the mortise and have it be exactly where it needs to be.

Am I making sense?

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!



These users thanked the author banjopicks for the post: Michaeldc (Tue Nov 09, 2021 11:35 am)
Top
 Profile  
 
PostPosted: Tue Nov 09, 2021 9:40 am 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1480
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
Woodie G wrote:
Has anyone seen any real evidence that a neck block extension supporting the top - versus the slipper foot, which seems like it actually provides some resistance to back flattening - does anything useful in resisting the body distortion that eventually leads to the necessity of a neck reset?

Having seen enough Martins with the neck block extensions versus those without coming in for work, it seems like time between neck resets has decreased with the extensions, rather than increased. I know their extensions are not physically tied into the UTB, but I would have thought that any extension supporting the top would have been helpful.


Hi Woodie,

I’ve only got 9yrs of data with this design, hardly a long look into the future. I am still in contact with the owner of #1 which is doing great. It has only needed the seasonal TR adjustment, and is so far running the original saddle. The guitar is his main gigging and recording rig and he has beat the heck out of it. This includes wearing a hole through the top. The finish on the other hand is toast! EM6k over z-poxy. He refuses to let me fix it…

Best, M


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 33 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: TimAllen and 11 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com