Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sat Jul 26, 2025 9:33 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 4:12 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 20, 2010 11:20 pm
Posts: 502
Location: Kurtistown, Hawaii
First name: Bob
Last Name: Gleason
City: Kurtistown
State: Hawaii
Zip/Postal Code: 96760
Country: USA
Focus: Build
Status: Amateur
Now that I'm involved in making some lap steels that require templates for routing cavities in solid wood, I'm wanting some clear Lexan templates for inside cuts, rather than the material I usually use so that I can see what I'm doing more easily. Normally, I'm just cutting Lexan on an outside line on the bandsaw and sanding to the line. Can't do that with inside cuts. No problem making the MDF template pattern for routing the Lexan, but I've had a couple of instances of the router wanting to melt and grab the polycarbonate when I try to pattern rout it. Just wondering about any learned advice on router bits, speeds, tips, etc. Thanks, Bob


You do not have the required permissions to view the files attached to this post.

_________________
“ The meaning of life is to find your gift and the purpose of life is to give it away” Pablo Picasso


Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 4:22 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Mar 01, 2011 1:32 pm
Posts: 3470
First name: Alex
Last Name: Kleon
City: Whitby
State: Ontario
Zip/Postal Code: L1N8X2
Country: Canada
Focus: Build
Status: Amateur
Try removing most of the waste with Forster bits in a drill press so that you only have to route 1/16" plus the peaks left from the bits.

Alex

_________________
"Indecision is the key to flexibility" .... Bumper sticker



These users thanked the author Alex Kleon for the post: Pegasusguitars (Mon Aug 01, 2016 11:14 pm)
Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 4:58 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Feb 29, 2008 2:41 pm
Posts: 312
How much are you trying to rout at once? Multiple passes are the way to go.

_________________
https://soundcloud.com/jeffreylsuits/he ... -runnin-13


Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 5:10 pm 
Offline
Contributing Member
Contributing Member

Joined: Sat Aug 27, 2011 1:59 pm
Posts: 385
First name: Ken
Last Name: Lewis
City: Mt. Pearl
State: NL
Country: Canada
Focus: Build
Status: Amateur
What Alex said. The less you have to take the better. Eliminate any source for vibration by clamping the lexan
down, etc. In general I find lexan a pita to route. Maybe someone else has the bees knees method to share??
Ken



These users thanked the author Ken Lewis for the post: Pegasusguitars (Mon Aug 01, 2016 11:13 pm)
Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 5:42 pm 
Offline
Walnut
Walnut

Joined: Wed Apr 18, 2012 7:19 pm
Posts: 21
First name: Jamie
Last Name: Martus
City: Leonard
State: MI
Country: U.S.
Focus: Repair
Status: Semi-pro
If you are going to use the templates less than a couple dozen times try making them out of .25" masonite hardboard. Flood the edges with thin CA to harden them up. It doesn't take care of your visibility concern but is MUCH safer! I've heard enough horror stories to be leary of pattern routing with lexan.

Sent from my SM-G920V using Tapatalk



These users thanked the author dustyjeans for the post: Pegasusguitars (Mon Aug 01, 2016 11:13 pm)
Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 6:19 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Mon Jan 28, 2008 5:21 am
Posts: 4915
Location: Central PA
First name: john
Last Name: hall
City: Hegins
State: pa
Zip/Postal Code: 17938
Country: usa
Focus: Build
Status: Professional
Routing lexan isn't that hard but you have to allow for the variables and Heat is the killer I use a 2 flute mill bit up cut in a blind hole and since your cutting this in a few passes you must plan for that . I will turn the router as slow as it will go. Spray the surface with water that has a touch of soap in it for coolant and lube. Take about 1/6 at a time cutting as fast as you can. The heat will go 1 of 3 places tool , work or chip. You want to get the heat in the chip. I would make a pattern then apply some tape and coat it with CA.Don't use so much that you glue the tape to the pattern.Once you are through the material remove the tape and make a clean out cut again spraying with the water and soap solution.
I used to machine a lot of lexan and polycarbonate . Lexan did cut the best so be sure you getting lexan not polycarbonate.

_________________
John Hall
blues creek guitars
Authorized CF Martin Repair
Co President of ASIA
You Don't know what you don't know until you know it



These users thanked the author bluescreek for the post: Pegasusguitars (Mon Aug 01, 2016 11:13 pm)
Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Mon Aug 01, 2016 11:23 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 20, 2010 11:20 pm
Posts: 502
Location: Kurtistown, Hawaii
First name: Bob
Last Name: Gleason
City: Kurtistown
State: Hawaii
Zip/Postal Code: 96760
Country: USA
Focus: Build
Status: Amateur
Thanks for all the replies. Sounds like I need to slow everything down. The router, the feed, me!

_________________
“ The meaning of life is to find your gift and the purpose of life is to give it away” Pablo Picasso


Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Tue Aug 02, 2016 6:05 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Mar 01, 2011 1:32 pm
Posts: 3470
First name: Alex
Last Name: Kleon
City: Whitby
State: Ontario
Zip/Postal Code: L1N8X2
Country: Canada
Focus: Build
Status: Amateur
Pegasusguitars wrote:
Thanks for all the replies. Sounds like I need to slow everything down. The router, the feed, me!


Don't slow down the feed rate - you want to keep the router bit moving across the lexan quickly, but like John said, slow down the rpm of the router. You can fine tune your process using some scrap pieces of lexan. You want shavings coming off of the bit, same as when you are routing wood.

Alex

_________________
"Indecision is the key to flexibility" .... Bumper sticker


Top
 Profile  
 
 Post subject: Re: ROUTING LEXAN
PostPosted: Tue Aug 02, 2016 7:03 am 
Offline
Koa
Koa

Joined: Sat May 19, 2007 11:03 am
Posts: 1737
Location: Litchfield MI
Focus: Build
Status: Professional
Shallow cuts for sure -- but a proprietary plastic cutting bit (which are single flute) goes a l long way in simplifying the process.

http://www.bamcarbide.com/acrylic.html

_________________
Ken Cierp

http://www.kennethmichaelguitars.com/


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: Bing [Bot] and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com