Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Mon Aug 04, 2025 2:21 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 27 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Referral job
PostPosted: Thu Dec 15, 2011 4:16 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
Here is the referral I got, it's not a really bad repair either.

Here is a Taylor 414CE with Ovankol side (I thought it was koa because of the flame, didn't look closely). According to the luthier the owner tried to reglue it with CA glue. The luthier just thought he slap some more titebond to the loose bridge and clamp, but in reality the bridge really needs to come off...

Image

Image

Image

Image

Here is the setup:

Image

Image

It took a while... and I got concerned when the soundboard got a bit hot too so I continued without the shield. But eventually the glue let go.

Image

I don't know if it was the heating to remove the bridge, or conditions that caused the bridge to come loose in the first place, but the wings are slightly warped. I tried to correct it by soaking it in boiling water but it did not help. So I used an iron to flatten it as much as I can, then sanded the bottom flat.

Image

Image

Image

So finally I flattened the bottom and routed the ledge back in (Taylor bridge has a ledge that simplifies gluing), I heated some hide glue and clamped it back on:

Image

Image

Will string it up tomorrow and see how it sounds...

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Thu Dec 15, 2011 9:34 am 
Offline
Mahogany
Mahogany

Joined: Sun Aug 30, 2009 6:27 pm
Posts: 44
First name: Peter
Last Name: Johnson
Country: Ceridigion, Wales
Well done Tai [:Y:]


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Thu Dec 15, 2011 9:47 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5900
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Looking good.
Next time you boil a bridge.... make tea. laughing6-hehe

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Thu Dec 15, 2011 10:04 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
Chris Pile wrote:
Looking good.
Next time you boil a bridge.... make tea. laughing6-hehe


The water did sort of turn tea colored... but I somehow doubt Ebony juice is very healthy...

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Thu Dec 15, 2011 6:57 pm 
Offline
Koa
Koa

Joined: Sat Apr 19, 2008 10:08 pm
Posts: 1958
Location: Missouri
First name: Patrick
Last Name: Hanna
State: Missouri
Country: USA
Looks to me like you did a good job. I would not have attempted such a repair, except on my own personal guitar. Let us know how it goes when it's strung up again.


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Thu Dec 15, 2011 8:53 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
cphanna wrote:
Looks to me like you did a good job. I would not have attempted such a repair, except on my own personal guitar. Let us know how it goes when it's strung up again.


When you're doing this for a living, you kinda don't have much of a choice except to do it on a customer's guitar. Plus when you're fixing a customer's guitar you gain valuable experience that you wouldn't get otherwise. There are risks, but as long as you're familiar with the step its not a bad risk to take.

Besides I am doing them a lot of favor because in Taiwan there's no one who is really qualified to fix an acoustic guitar.

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Fri Dec 16, 2011 4:27 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue May 13, 2008 10:44 am
Posts: 6262
Location: Virginia
Mmmmm Ebony soup. I've never heard of such a technique for getting bridge warp out. By the looks of your pics it almost appears that the bridge had glue applied only to the perimeter. You can see a defined glue line along the perimeter of the bridge but not in the middle. Do you suspect that's the case?


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Fri Dec 16, 2011 8:40 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
jfmckenna wrote:
Mmmmm Ebony soup. I've never heard of such a technique for getting bridge warp out. By the looks of your pics it almost appears that the bridge had glue applied only to the perimeter. You can see a defined glue line along the perimeter of the bridge but not in the middle. Do you suspect that's the case?


That's because Taylor like a few other manufacturer routes a microscopic lap into the perimeter of the bridge, so that they only have to cut a profile on the finish where the bridge is slightly smaller than the bridge itself, and the two pieces fit seamlessly without gap. However when I try to duplicate it I always end up with a small amount of gap in the corner of the bridge, possibly because Taylor uses precision CNC to duplicate very exact dimension whereas I have to approximate it with a router. I doubt I could even duplicate that even with a milling machine.

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sat Dec 17, 2011 7:31 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
An update:

There's a small gap in the corner and the luthier who referred me told me to do it over again, because that gap no matter how small is not acceptable, since that's what he was complaining about to begin with.

So I ended up taking the bridge off again and was wondering why that gap was there in the first place. I traced it down to the fact that since the bridge had warped, that part was already springing up and unless I make a new bridge (which is not something I wanted to do), all I could do is apply heat in that area and bend it down a little bit.

So this time I made a few dry runs before actually taking glue to the thing again. I made a few clamping blocks to put more pressure in that area and it looks like the gap has disappeared. So I tried again with glue and it seems to have worked, but there is still a .001" lip in the corner due to corner rounding... I just hope this is good enough because if not, I think I am going to commit Guitar-icide.

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sat Dec 17, 2011 3:09 pm 
Offline
Koa
Koa

Joined: Thu Jan 24, 2008 2:13 am
Posts: 902
Location: Caves Beach, Australia
Please don't be offended, But I think you have been extremely lucky not to seriously damage the guitar by the way you have approached this repair.
The foil masking which you used with a gap around the bridge like that could have lead to the finish blistering where exposed. A clothes iron really is not the right thing to use.
The warping of the bridge is to be expected when you heat one side of it, boiling is not the answer, and any bridge which has been soaked should not be leveled and glued in place in the time frame you have worked to.
You really do need to work to more realistic time frames and communicate that to the client


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sat Dec 17, 2011 8:34 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
No, I am not offended at all, in fact I am mostly humbled.

Other than the guitar repair blanket (which along with the controller, is a costly investment), I just can't think of a better tool than an iron or heat lamps. The problem being I need to find those spring arm work lamp that doesn't use LED or florescent technology because that's all I've managed to find these days. In fact I've heard rumors that they wanted to outlaw incandescent light bulbs because they're an energy waster. The issue being since LED and florescent lights are so efficient, they produce next to no heat...

If I do use light bulbs to heat a bridge, what wattage do I need?

I kinda wish there is a school which teaches repair technique, even better if it's online. I know many luthier school mostly teaches how to build a guitar and other building techniques.

It's little wonder that I got the referral job because that luthier doesn't have the ability to heat a bridge off without damage.

Also, thank God for Taylor's bulletproof UV poly I guess...

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sat Dec 17, 2011 9:42 pm 
Offline
Koa
Koa

Joined: Thu Jan 24, 2008 2:13 am
Posts: 902
Location: Caves Beach, Australia
I have an LMI bridge heating blanket sitting in my workshop, I have not used it yet but it is there when I need it.
Rather than buy the controller (and we are on 240V here so there controller was not suitable) I use a 1200 watt dimmer switch for the bending and repair blankets.
Frank Ford's site www.frets.com is as good a source of repair information as you will get
Here is his bridge regluing tutorial
http://www.frets.com/FRETSPages/Luthier ... uebr1.html


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 12:40 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jul 19, 2009 11:58 am
Posts: 35
First name: Tom
Last Name: Langseth
City: HORSESHOE BAY
State: TEXAS
Zip/Postal Code: 78657
Country: USA
Focus: Build
Status: Semi-pro
I agree with the use of your clothes-iron to loosen the bridge. Your insulation, however, was counter productive. I have found that several layers of corrugated cardboard-box material to act as a heat sink will protect the finish on the top. I think this trick came from Mr. Compiano, but not sure. Use at least 4 layers of the cardboard, cut out for the shape of the bridge, set your iron for linen and be patient. Hot glue will loosen in just a few minutes. Using a heating blanket is more involved, so I don't use mine any more.

Hope this helps,
Tom


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 1:35 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
tomlang wrote:
I agree with the use of your clothes-iron to loosen the bridge. Your insulation, however, was counter productive. I have found that several layers of corrugated cardboard-box material to act as a heat sink will protect the finish on the top. I think this trick came from Mr. Compiano, but not sure. Use at least 4 layers of the cardboard, cut out for the shape of the bridge, set your iron for linen and be patient. Hot glue will loosen in just a few minutes. Using a heating blanket is more involved, so I don't use mine any more.

Hope this helps,
Tom


4 layers of cardboard box material would be thicker than the bridge itself, so I'd be heating the cardboard and not the bridge. I mean each layer of cardboard is close to 1/8" thick.

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 2:05 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Sep 08, 2010 12:17 am
Posts: 1292
First name: John
Last Name: Arnold
City: Newport
State: TN
Zip/Postal Code: 37821
Country: USA
Focus: Repair
Status: Professional
For a shield, I use a single layer of white finish corrugated cardboard. The window is 1/8" smaller than the bridge all the way around. I use a 250 watt heat lamp. Heat lamp bulbs have a very long life....I have used the same bulb for over 20 years.
To straighten the bridge wings, I use a small heat gun (the kind used for electronics). It gets really hot. Holding the bridge in my hand, I press the corner against the work bench, reheating as necessary. It only takes a minute or so.

_________________
John


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 3:35 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
John Arnold wrote:
For a shield, I use a single layer of white finish corrugated cardboard. The window is 1/8" smaller than the bridge all the way around. I use a 250 watt heat lamp. Heat lamp bulbs have a very long life....I have used the same bulb for over 20 years.
To straighten the bridge wings, I use a small heat gun (the kind used for electronics). It gets really hot. Holding the bridge in my hand, I press the corner against the work bench, reheating as necessary. It only takes a minute or so.


So kinda like bending wood right?

What do you mean the kind of heat gun used for electronics... I've seen those butane powered thing that are used for shrinking tubings, is that what you mean? I was thinking a hair dryer may be safer...

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 8:53 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Feb 12, 2009 10:27 pm
Posts: 2109
Location: South Carolina
First name: John
Last Name: Cox
Focus: Build
Status: Amateur
You can buy very small heating irons for veneer use - Check out the hobby Model Airplane catalogues as well.... Look for the irons and heat guns they use to shrink the plastic wing coverings... They are frequently called "Sealing irons"

Here's an example, but the same place sells like 5 different ones:
http://www3.towerhobbies.com/cgi-bin/wt ... XHZ17&P=ML

Heat guns are like hair dryers - except they get MUCH hotter...Hot enough to burn you seriously....
Here's an example from the same place...
http://www3.towerhobbies.com/cgi-bin/wt ... LXHZ16&P=M

Once again - check out the Model Airplane folks or veneering supply catalogs for these products...

Thanks


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 9:12 am 
Offline
Contributing Member
Contributing Member

Joined: Wed Mar 05, 2008 1:44 pm
Posts: 706
First name: Wendy
Last Name: W
State: Arizona
Country: USA
Focus: Build
Status: Amateur
You said that you sanded the bottom of the bridge flat. Does the Taylor not have any dome to the top? Wouldn't you have to sand the bottom of the bridge to match the top doming? Or did I miss something?


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 10:11 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
callyrox wrote:
You said that you sanded the bottom of the bridge flat. Does the Taylor not have any dome to the top? Wouldn't you have to sand the bottom of the bridge to match the top doming? Or did I miss something?


The Taylor does have a dome, but it's fairly flat. I've noticed as I took the bridge off that it had absolutely no relief sanded into the bottom to match the top dome, I am not sure if its due to the bridge warping out of shape or that it had no relief in the first place. I had to remove quite a bit of wood before I was able to match the bridge to the body, and nothing I did otherwise corrected it.

I even checked Factory Fridays to confirm how they made their bridge, but I couldn't see if they had any bottom radius carved into the bridge.

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 10:48 am 
Offline
Contributing Member
Contributing Member

Joined: Wed Mar 05, 2008 1:44 pm
Posts: 706
First name: Wendy
Last Name: W
State: Arizona
Country: USA
Focus: Build
Status: Amateur
I would just lay a piece of sandpaper on the guitar in the bridge location and rub the bottom of the bridge back and forth until the entire bottom of the bridge is covered in sanding scratches. Then it should match the soundboard shape perfectly.
The problem with removing a lot of wood from the bridge is that you are changing the thickness of the bridge, which was originally matched to the neck angle and action of the guitar.


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 10:58 am 
Offline
Contributing Member
Contributing Member

Joined: Wed Mar 05, 2008 1:44 pm
Posts: 706
First name: Wendy
Last Name: W
State: Arizona
Country: USA
Focus: Build
Status: Amateur
Were the wings of the bridge warped like that before you removed it? In the third picture, when it is still on the guitar, the wings don't look warped. Maybe it just doesn't show in the picture. I would talk to Taylor and see what they say about the warped wings. Maybe you could get a new bridge from them if they warped while on the guitar.


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 11:10 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
callyrox wrote:
Were the wings of the bridge warped like that before you removed it? In the third picture, when it is still on the guitar, the wings don't look warped. Maybe it just doesn't show in the picture. I would talk to Taylor and see what they say about the warped wings. Maybe you could get a new bridge from them if they warped while on the guitar.


I think it may have warped due to being left in a hot car, but it was warped from the beginning.

In any case if the guitar was still under warranty, having a third party work on it pretty much voids all warranty.

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Sun Dec 18, 2011 5:30 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Feb 12, 2009 10:27 pm
Posts: 2109
Location: South Carolina
First name: John
Last Name: Cox
Focus: Build
Status: Amateur
While that's theoretically true and all... they may not have Taylor factory authorized service in Taiwan... If that's the case - it's a long and expensive trip back to the USA...

Thanks


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Mon Dec 19, 2011 10:34 am 
Offline
Contributing Member
Contributing Member

Joined: Wed Mar 05, 2008 1:44 pm
Posts: 706
First name: Wendy
Last Name: W
State: Arizona
Country: USA
Focus: Build
Status: Amateur
Actually I wasn't suggesting sending the guitar back for warranty work. I just thought that Taylor might find it interesting that the wings of the bridge warped and that they might be willing to provide a new bridge regardless of warranty, especially considering the location of the guitar. Is it common for bridge wings to warp? I've never seen that before. I would think a lot worse would happen to a guitar left in a hot car, before the bridge wings would warp. I'm just wondering if it is due to some defective character of that piece of wood.


Top
 Profile  
 
 Post subject: Re: Referral job
PostPosted: Mon Dec 19, 2011 10:38 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Sep 24, 2008 8:55 pm
Posts: 3820
Location: Taiwan
First name: Tai
Last Name: Fu
City: Taipei
Country: Taiwan
Focus: Repair
Status: Semi-pro
callyrox wrote:
Actually I wasn't suggesting sending the guitar back for warranty work. I just thought that Taylor might find it interesting that the wings of the bridge warped and that they might be willing to provide a new bridge regardless of warranty, especially considering the location of the guitar. Is it common for bridge wings to warp? I've never seen that before. I would think a lot worse would happen to a guitar left in a hot car, before the bridge wings would warp. I'm just wondering if it is due to some defective character of that piece of wood.


It might be... because if the warping was caused by an external force like heat, then it should return to normal once you boil the bridge in water for a few minutes.

Bridge wing seem more affected by conditions though because its so thin

_________________
Cat-gut strings are made from kitten guts, stretched out to near breaking point and then hardened with grue saliva. As a result these give a feeling of Pain and anguish whenever played, and often end up playing themselves backwards as part of satanic rituals.

Typhoon Guitars
http://www.typhoon-guitars.com


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 27 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com