***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Aug 14, 2025 3:54 am


Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
coach
PostPosted: Wed Oct 20, 2010 9:51 am 
Offline
Cocobolo
Cocobolo

Joined: Thu Feb 19, 2009 1:31 pm
Posts: 158
Location: Atlanta GA
First name: Sean
Focus: Build
Status: Amateur
Anyone ever use a power miter saw to cut this 15 degree cut? Will it work accurately?

_________________
change isn't synonymous with improvement
instagram.com/bucketguitars/
Top
 Profile  
 
TonyKarol
PostPosted: Wed Oct 20, 2010 10:14 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Sep 09, 2005 7:51 am
Posts: 3786
Location: Canada
If you have the reach in the blade, I dont see why not .... but you still might have to touch it up with a plane. I just cut it close on the bandsaw, then clean up with a plane .. it takes about 4 minutes and its ready to glue ... try it, its not that hard.

_________________
Tony Karol
www.karol-guitars.com
"let my passion .. fulfill yours"
Top
 Profile  
 
Aj White
PostPosted: Wed Oct 20, 2010 10:16 am 
Offline
Walnut
Walnut

Joined: Tue Sep 28, 2010 9:34 pm
Posts: 18
First name: Aj
Last Name: White
City: Hangtown
Country: USA
Focus: Build
Status: Amateur
I just did it on my number one, made up a little 90 degree fence and it didn't go so well. I was able to plane everything flat after wards though. I think the ticket would be to make a wedge style fence so your neck blank is better supported and the saw blade would be fully adjusted left. I think I could make it work a lot better and will try it again next time.
Top
 Profile  
 
Corky Long
PostPosted: Wed Oct 20, 2010 10:29 am 
Offline
Koa
Koa

Joined: Tue Feb 24, 2009 9:23 am
Posts: 1372
First name: Corky
Last Name: Long
City: Mount Kisco
State: NY
Country: USA
Focus: Build
Status: Amateur
TonyKarol wrote:
If you have the reach in the blade, I dont see why not .... but you still might have to touch it up with a plane. I just cut it close on the bandsaw, then clean up with a plane .. it takes about 4 minutes and its ready to glue ... try it, its not that hard.


That's what I do as well - except I built a simple sled, at 15 degrees, which fits into the guide slot on my bandsaw. It's still not totally accurate, and you have to feed it very slowly until the blade cuts the angle properly (bandsaw likes to deflect away from the angle of the neck blank), but it works fine after a few passes of a sharp plane.
Top
 Profile  
 
sttelnoj
PostPosted: Wed Oct 20, 2010 8:08 pm 
Offline
Mahogany
Mahogany

Joined: Thu May 20, 2010 8:24 pm
Posts: 44
First name: jon
Last Name: letts
City: leicestershire
Zip/Postal Code: le676pz
Country: uk
Focus: Build
Status: Semi-pro
yes. i dont see the point of setting up fences at the best of times. bandsaw by hand and then clamp the neck and headstock (spun round) together and plane the both together. perfecto! i also go 13 degrees.
Top
 Profile  
 
sttelnoj
PostPosted: Thu Oct 21, 2010 12:05 am 
Offline
Mahogany
Mahogany

Joined: Thu May 20, 2010 8:24 pm
Posts: 44
First name: jon
Last Name: letts
City: leicestershire
Zip/Postal Code: le676pz
Country: uk
Focus: Build
Status: Semi-pro
Todd Stock wrote:
I always clean up with a hand plane, so a band saw or back saw cut is fine...a couple wire brads set outside the peghead outline can help keep things lined up.

yep, just like that!
Top
 Profile  
 
Ti-Roux
PostPosted: Thu Oct 21, 2010 12:16 am 
Offline
Koa
Koa
User avatar

Joined: Wed Oct 21, 2009 7:46 pm
Posts: 950
First name: Francis
Last Name: Richer
City: Montréal
State: Québec
Zip/Postal Code: H4G 2Z2
Country: Canada
Focus: Build
Status: Semi-pro
Band saw by hand and plane for me too. 16-17 degrees on my classical.

Francis

_________________
Francis Richer, Montréal
Les Guitares F&M Guitars
Top
 Profile  
 
Beth Mayer
PostPosted: Thu Oct 21, 2010 1:27 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 13, 2010 12:46 am
Posts: 1247
First name: Beth
Last Name: Mayer
City: Tucson
State: AZ
Country: United States
Focus: Build
Status: Amateur
This thread will save me time and forearm stress....I was taught to use a sanding block to true the 15 degree pieces. Never even thought about using a plane...duh! I'll be doing that on my next one. Have always dreaded the scarf cutting because the bandsaw isn't super accurate, even with my very clever jig, and have had to sand for a long time before getting a perfect joint. Thanks guys! Beth
Top
 Profile  
 
coach
PostPosted: Thu Oct 21, 2010 11:47 am 
Offline
Cocobolo
Cocobolo

Joined: Thu Feb 19, 2009 1:31 pm
Posts: 158
Location: Atlanta GA
First name: Sean
Focus: Build
Status: Amateur
Thanks for all the tips!

_________________
change isn't synonymous with improvement
instagram.com/bucketguitars/
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 42 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com