Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 11:46 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 14 posts ] 
Author Message
PostPosted: Sat Jul 17, 2021 2:14 pm 
Offline
Koa
Koa
User avatar

Joined: Mon Nov 24, 2008 12:17 pm
Posts: 1161
City: Escondido
State: CA
Zip/Postal Code: 92029
Country: USA
Focus: Build
Status: Semi-pro
I’ve been using a Fox bending jig for twenty years, and have never liked the cutaway solution. Something like in this picture. Image


It’s bulky and seems to come at the cutaway at a bad angle. I’ve notice factory jigs tend to press in line with the guitar centerline.

In any case, if love to see if anyone has come up with a better mousetrap in this community. How do you get your cutaways bent?


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Sat Jul 17, 2021 3:44 pm 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1445
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
My setup is basically an adjustable Fox bender. You can change the waist location as well as the center of effort for the cutaway. Works great!


You do not have the required permissions to view the files attached to this post.



These users thanked the author Michaeldc for the post: Pmaj7 (Sun Jul 18, 2021 12:53 pm)
Top
 Profile  
 
PostPosted: Sat Jul 17, 2021 3:48 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4777
I use this to bend Florentine cutaways. I have not done a Venetian.

Image

Image

Image


Sent from my iPhone using Tapatalk



These users thanked the author James Orr for the post: Tim Mullin (Sat Jul 17, 2021 7:37 pm)
Top
 Profile  
 
PostPosted: Sat Jul 17, 2021 9:16 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Jan 27, 2008 8:44 pm
Posts: 98
Location: Woodstock, Illinois
First name: Kent
Last Name: Fishburn
City: Woodstock
State: Illinois
Focus: Build
Status: Amateur
I love this bender Dan Koentopp uses.
https://www.youtube.com/watch?v=HQMgt_kkMA0

Kent



These users thanked the author kfish for the post (total 5): Joe Beaver (Sat Jul 24, 2021 4:33 pm) • Pmaj7 (Mon Jul 19, 2021 11:39 pm) • Durero (Sun Jul 18, 2021 12:39 pm) • rlrhett (Sun Jul 18, 2021 12:19 pm) • Michaeldc (Sat Jul 17, 2021 9:27 pm)
Top
 Profile  
 
PostPosted: Sun Jul 18, 2021 11:14 am 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1445
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
kfish wrote:
I love this bender Dan Koentopp uses.
https://www.youtube.com/watch?v=HQMgt_kkMA0

Kent


Genius!!

I’ve been chewing on this since you posted it. Granted he’s bending 2-1/2” maple side (easy), but it seems like it should work with a 4-3/4” dread side. One may have to up the weight a little.

Thanks for sharing! M


Top
 Profile  
 
PostPosted: Sun Jul 18, 2021 11:41 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Jan 27, 2008 8:44 pm
Posts: 98
Location: Woodstock, Illinois
First name: Kent
Last Name: Fishburn
City: Woodstock
State: Illinois
Focus: Build
Status: Amateur
Michaeldc wrote:
kfish wrote:
I love this bender Dan Koentopp uses.
https://www.youtube.com/watch?v=HQMgt_kkMA0

Kent


Genius!!

I’ve been chewing on this since you posted it. Granted he’s bending 2-1/2” maple side (easy), but it seems like it should work with a 4-3/4” dread side. One may have to up the weight a little.

Thanks for sharing! M


I asked him about how long it takes to bend and he said about 10 minutes to complete the bend and then he cooks it for 15 minutes. I was thinking that was a cinderblock for a weight which should be plenty but on second look I guess it's not. So yeah, maybe a little more weight, though he does a lot of different woods in his builds. I don't know if he varies the weight.


Top
 Profile  
 
PostPosted: Sun Jul 18, 2021 11:44 am 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1445
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
kfish wrote:
Michaeldc wrote:
kfish wrote:
I love this bender Dan Koentopp uses.
https://www.youtube.com/watch?v=HQMgt_kkMA0

Kent


Genius!!

I’ve been chewing on this since you posted it. Granted he’s bending 2-1/2” maple side (easy), but it seems like it should work with a 4-3/4” dread side. One may have to up the weight a little.

Thanks for sharing! M


I asked him about how long it takes to bend and he said about 10 minutes to complete the bend and then he cooks it for 15 minutes. I was thinking that was a cinderblock for a weight which should be plenty but on second look I guess it's not. So yeah, maybe a little more weight, though he does a lot of different woods in his builds. I don't know if he varies the weight.


He’s got an earlier YouTube vid from before he added the half cinderblock. The weight makes it look so easy


Top
 Profile  
 
PostPosted: Sun Jul 18, 2021 12:20 pm 
Offline
Koa
Koa
User avatar

Joined: Mon Nov 24, 2008 12:17 pm
Posts: 1161
City: Escondido
State: CA
Zip/Postal Code: 92029
Country: USA
Focus: Build
Status: Semi-pro
kfish wrote:
I love this bender Dan Koentopp uses.
https://www.youtube.com/watch?v=HQMgt_kkMA0

Kent

Wow! Now that’s what I’m talking about. So ingenious!

I’m going to have to study that video a lot to fully understand that jig.


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Sun Jul 18, 2021 4:04 pm 
Offline
Cocobolo
Cocobolo

Joined: Sun Oct 09, 2016 12:18 pm
Posts: 383
Location: Somerset UK
State: West Somerset
Country: UK
Focus: Build
Status: Amateur
The thing is with bending cutaways is that you have this double - Z - bend if you like. And what you have to do is to support the wood on the outside of both of those curves. To do this you have to tension both steel slats I have constructed an admittedly rather crude device to do this. It is not my idea. I think it was Mike Doolin who first suggested this in an early Gal and others have developed the idea.

The trick is that the slats and the sides are fixed at the tail end and springs are used to tension the slats both above and below the side wood to provide support on the outside of the two bends. I always do cutaways - fairly sharp - and this has worked with few failures for me.

Hopefully the pics show the general idea. Cheers Dave


You do not have the required permissions to view the files attached to this post.



These users thanked the author Dave m2 for the post (total 4): James Orr (Tue Jul 20, 2021 10:29 am) • Pmaj7 (Mon Jul 19, 2021 3:27 am) • rlrhett (Sun Jul 18, 2021 5:01 pm) • CarlD (Sun Jul 18, 2021 4:49 pm)
Top
 Profile  
 
PostPosted: Mon Jul 19, 2021 9:52 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3289
Location: Alexandria MN
Based on something I think I saw here I made an extension with a pulley and instead of springs ran a cord from the slats over the pulley and put on about 5lbs to tension the sandwich.

Thought I had an in action picture but can’t find it. It has worked well.

One nice thing about double sides and a tight cutaway is you can bend both together but with a much thinner thickness.

_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.


Top
 Profile  
 
PostPosted: Tue Jul 20, 2021 5:30 pm 
Offline
Cocobolo
Cocobolo

Joined: Sun Oct 09, 2016 12:18 pm
Posts: 383
Location: Somerset UK
State: West Somerset
Country: UK
Focus: Build
Status: Amateur
Terence that is another way to do it but although I haven’t measured it I suspect the springs I use are probably exerting rather more force. You are presumably bending pretty thin stuff if you are building double sides.

Rather poor pics but I move the anchor points for the springs forwards as the bend is formed to keep the tension from becoming too great. I guess a weight on a pulley has the same effect.

I am working with about 1.8 mm for the cutaway sides - a bit more for the non cutaway. And I do do a pretty sharp cutaway.

Out of interest how are glueing the two laminates?

Dave



These users thanked the author Dave m2 for the post: Terence Kennedy (Wed Jul 21, 2021 9:03 am)
Top
 Profile  
 
PostPosted: Wed Jul 21, 2021 1:16 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3289
Location: Alexandria MN
Unibond 800 Dave. It’s worked great for me. Clamped over an inside form with shaped cauls. It also serves as the bending form.

_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.


Top
 Profile  
 
PostPosted: Thu Jul 22, 2021 10:48 am 
Offline
Cocobolo
Cocobolo

Joined: Sun Oct 09, 2016 12:18 pm
Posts: 383
Location: Somerset UK
State: West Somerset
Country: UK
Focus: Build
Status: Amateur
Thanks Terence. Laminated sides is something I am likely to try at some point.


Dave


Top
 Profile  
 
PostPosted: Sat Jul 24, 2021 4:33 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
KFish,
That is the coolest, most versatile bender I have ever seen. I would love to know what he uses for a friction clutch. I don't notice him tightening anything as he goes.
Well done.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 14 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: GregHolmberg and 64 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com