| Official Luthiers Forum! https://www.luthiersforum.com/forum/ |
|
| Which dremel bit for fine inlay work ? https://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=44746 |
Page 1 of 1 |
| Author: | Cablepuller [ Sun Dec 14, 2014 3:43 pm ] |
| Post subject: | Which dremel bit for fine inlay work ? |
Hi what dremel bit do you use for fine pearl inlay work please Thanks |
|
| Author: | DennisK [ Sun Dec 14, 2014 3:54 pm ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
1/16" bits are what I go through the most of. But you also need at least 1/32" for detailed work. 1/64" is my smallest, and I don't use it very often, but it is nice to have around when working in very hard woods. Softer woods, you can just pick out any corners with a knife after the 1/32" bit. And 1/8" is nice to have around for clearing out large areas, although it can be done by hand with a chisel too. |
|
| Author: | Cablepuller [ Sun Dec 14, 2014 4:01 pm ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
Thanks..do you stick to genuine dremel bits or the cheaper options on ebay |
|
| Author: | bluescreek [ Sun Dec 14, 2014 6:05 pm ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
don't use them I use these it is a 1/32 end mill up cut. http://www.bqtool.com/square-end-mills.html you have to call and order them special. Great tools for inlay 1/8 in shaft |
|
| Author: | Pat Hawley [ Sun Dec 14, 2014 6:11 pm ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
I ask my dentist for used dental drill bits. There's quite a variety but the smallest one seems to be just under 1/32" and I find it works quite nicely. Plus, the price is right (i.e. free). Pat |
|
| Author: | cphanna [ Sun Dec 14, 2014 7:07 pm ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
I went to my dentist friend, who supplied me with a variety of dental burrs. I believe many of them are carbide or otherwise very hard. In any event, when they are no longer sharp enough to be useful for his work, they still have tons of life in them for my work. Dental burrs will chuck into the smaller sized Dremel collet very nicely (use the wrench to snug them very tightly) and they cut like crazy. They come in ball shapes, tapered (for undercut), straight sided, etc. Tell your dentist what you need. Your dentist is probably throwing his used ones away. My dentist runs them through his sterilizer before he gives them to me. I don't know that you need to go that far, but you might drop any hand-offs into a jar of alcohol for a while before you use them--and be sure to wash your hands VERY carefully if you've touched them with bare fingers. |
|
| Author: | Robbie_McD [ Sun Dec 14, 2014 8:49 pm ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
Agreed with Dennis and John, I use 1/16" upcut carbide end mills for most inlay work, and go to 1/32 for the fine stuff - 1/8 for hogging out. I rarely inlay other than ebony, which is pretty forgiving if you fill with epoxy mixed with Laskin's magic black powder (lampblack and ebony dust, methinks) |
|
| Author: | Joe Beaver [ Mon Dec 15, 2014 1:41 am ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
I also use 1/32" & 1/6" mostly. For inlaying sharp pointed areas I sometimes use smaller, like 1/64" I get mine here. Cost more but they are good quality. http://www.american-carbide.com/MicroEn ... oducts.php |
|
| Author: | Colin North [ Mon Dec 15, 2014 4:17 am ] |
| Post subject: | Re: Which dremel bit for fine inlay work ? |
OK, no expert here, but following a recommendation on OLF, I bought 8 bits, (2 new, 6 Lightly Used, Fish Tail) from http://drillbitsunlimited.com/Default.aspx Including postage they still came in at less that the import duty/charges threshold, at about $24. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|