Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sat Nov 07, 2026 8:51 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Tue Aug 11, 2026 3:09 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Jul 31, 2010 4:03 pm
Posts: 209
First name: Neil
Last Name: Kwak
State: PA
Country: United States
Focus: Build
Status: Amateur
Hi all,

I kicked off my 5th build in late spring. It's going to be an EIR/WRC OM.

I made some good progress this week getting the sides assembly put together and inlaying a rosette using rosewood scrap and zipflex.

Image

Image

I've added the lining to the other side and have to "drive the bus" just a little more before I turn my attention to the cedar top but I'm really proud how the rosette turned out. I'm currently cutting the brace stock.

I have most of the materials and hope to make better progress with this one and work faster and more efficiently than I have in previous builds.



These users thanked the author nkwak for the post: rbuddy (Thu Aug 13, 2026 2:44 pm)
Top
 Profile  
 
PostPosted: Tue Sep 22, 2026 12:48 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Jul 31, 2010 4:03 pm
Posts: 209
First name: Neil
Last Name: Kwak
State: PA
Country: United States
Focus: Build
Status: Amateur
The top is just about braced up: 5/16" sitka with the tone bars inlet into the X brace and an osage orange bridge plate. Years ago when I asked Tim McKnight for advice on my first build he shared with me how Somogyi doesn't taper the No. 1 brace into the sides so I'm doing it again here. I also did it on my fourth.

Image


Top
 Profile  
 
PostPosted: Tue Sep 29, 2026 7:38 am 
Offline
Site Admin
User avatar

Joined: Mon Dec 27, 2004 5:02 am
Posts: 8579
Location: United States
First name: Lance
Last Name: Kragenbrink
City: Vandercook Lake
State: Michigan
Zip/Postal Code: 49203
Country: USA
Focus: Build
Status: Semi-pro
looks like it'll be a beauty!

_________________
Support the OLF! Bookmark our STEWMAC link Today!
Lance@LuthiersForum.com


Top
 Profile  
 
PostPosted: Sat Oct 17, 2026 10:28 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Jul 31, 2010 4:03 pm
Posts: 209
First name: Neil
Last Name: Kwak
State: PA
Country: United States
Focus: Build
Status: Amateur
LanceK wrote:
looks like it'll be a beauty!


Thanks! The bracing is now carved, tapered, scalloped and sanded smooth. All that's left is the popsicle brace on the upper bout.

Image

PS: the blown out top is from my first build completed in 2013. It developed problems (too thin, lifting braces) so I removed it and am using it as inspiration to retop No. 1 too eventually.



These users thanked the author nkwak for the post (total 2): rbuddy (Sun Oct 18, 2026 12:58 pm) • Kbore (Sun Oct 18, 2026 10:17 am)
Top
 Profile  
 
PostPosted: Sun Oct 18, 2026 4:59 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7597
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Looking good. I’m also re-topping one of my early builds. A nice guitar but the top was just over braced.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Mon Oct 19, 2026 10:09 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Jul 31, 2010 4:03 pm
Posts: 209
First name: Neil
Last Name: Kwak
State: PA
Country: United States
Focus: Build
Status: Amateur
Yes, that one had a bad glue joint somewhere in the top though. It looks like it was actually the bridge plate. That gives me cold feet for this one but I tried to make sure that I had enough gobars to exert pressure abd even used a maple caul.

Image

In the meantime, this one is less an actual OM and more of a small jumbo (SJ) as it is as deep as a dreadnought.

BTW, No. 1 was actually an OLF MJ but I’ve never cared for the tight waist. One thing that did intrigue me was the option for an X brace on the back. I’m tempted to do either that or adopt the ladder bracing from a Martin dreadnought which has two flatter and fatter braces on the lower bout. This begs the questions though of what are the advantages and drawbacks of either?



These users thanked the author nkwak for the post: SteveSmith (Tue Oct 20, 2026 5:56 am)
Top
 Profile  
 
PostPosted: Thu Nov 05, 2026 8:10 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Jul 31, 2010 4:03 pm
Posts: 209
First name: Neil
Last Name: Kwak
State: PA
Country: United States
Focus: Build
Status: Amateur
I was told elsewhere that the end grain on this sides braces may cause problems down the road. I am going to take chisel to all of it on the lower bouts and redo the lining and put in less side braces.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com