Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 8:10 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: Dissolving old glue
PostPosted: Wed Dec 12, 2018 10:58 am 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
Is there a way to dissolve old glue that is on wood? As a sub question, is there a way to tell by appearance what kind of glue a person is dealing with? I'm working on cleaning up a failed headstock repair (see earlier post about the '57 Gibson) and there's a lot of glue. If I can avoid hours and hours of scraping the lions share of the glue off the surface of this break that would be awesome!

I did try using a soldering iron and damp towel but it seemed to have no effect, this particular glue almost looks like lacquer, it's clear and has a nice gloss.


Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Wed Dec 12, 2018 12:13 pm 
Offline
Cocobolo
Cocobolo

Joined: Thu Feb 09, 2012 4:10 pm
Posts: 272
First name: Chris
Last Name: Reed
City: Stowmarket
State: Suffolk
Zip/Postal Code: IP14 2EX
Country: UK
Focus: Build
Status: Amateur
I can't tell from the photos on the other thread, but if it *is* water soluble then it might be hide glue. Steam ought to have made the surface sticky if so, but old hide glue takes quite some time to start to dissolve/liquefy. Your damp cloth might not have produced enough steam, or for long enough, to soften the glue.

Get a cotton wool bud and a cup of hot water, and get a small part of the glue surface wet. Keep wiping with a hot bud (rinse to get it hot again). After a few minutes you might see a change in the surface appearance of the bit you're working on, and the bud starts to feel sticky. If so, you're winning! Basically, keep going until it's all gone. It will take ages, but if it's hide glue and you re-glue using hide, then leaving a very thin film of old glue on the surface is fine because you've partially reactivated it during cleaning, and although it will dry the new hide glue should reactivate it. But you mustn't leave more than a smear!

If this doesn't work then it's not water-soluble. I believe that acetone might be the next thing to try, but wait for words from others who know rather than just believe :)



These users thanked the author profchris for the post: Conor_Searl (Wed Dec 12, 2018 12:23 pm)
Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Wed Dec 12, 2018 1:45 pm 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
profchris wrote:
but old hide glue takes quite some time to start to dissolve/liquefy.


Just to get some perspective are we talking 5 minutes or a half an hour?


Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Wed Dec 12, 2018 4:29 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2010 9:06 pm
Posts: 2739
Location: Magnolia DE
First name: Brian
Last Name: Howard
City: Magnolia
State: Delaware
Zip/Postal Code: 19962
Country: United States
Focus: Repair
Status: Professional
Could be epoxy..... Most unqualified techs prefer it as they think it will work better. Most of the failed repaired head breaks I see were done in epoxy. Stripper with MEC in it (BTW if you haven't heard the stuff with MEC is going bye bye from the stores next year...). will work but it will not be absolutely clean when done and vapors are deadly. Oh and any finish in the general area will be toast too. Epoxy will also release with heat, usually about 300 D F. again toasting the finish and possibly weakening other joints like the FB.

_________________
Brian

You never know what you are capable of until you actually try.

https://www.howardguitarsdelaware.com/



These users thanked the author B. Howard for the post: Conor_Searl (Thu Dec 13, 2018 12:16 pm)
Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Wed Dec 12, 2018 8:03 pm 
Offline
Cocobolo
Cocobolo

Joined: Mon Mar 25, 2013 7:44 pm
Posts: 123
First name: Wayne
Last Name: Brown
City: Huntersville
State: NC
Zip/Postal Code: 28078
Country: USA
Focus: Build
Status: Amateur
It's probably not Titebond but as a matter of information, vinegar will desolve Titebond glue. I had read this somewhere and it worked great on one of my repairs.

Wayne



These users thanked the author Wayne Brown for the post: Conor_Searl (Wed Dec 12, 2018 10:03 pm)
Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Thu Dec 13, 2018 10:50 am 
Offline
Cocobolo
Cocobolo

Joined: Thu Feb 09, 2012 4:10 pm
Posts: 272
First name: Chris
Last Name: Reed
City: Stowmarket
State: Suffolk
Zip/Postal Code: IP14 2EX
Country: UK
Focus: Build
Status: Amateur
Conor_Searl wrote:
profchris wrote:
but old hide glue takes quite some time to start to dissolve/liquefy.


Just to get some perspective are we talking 5 minutes or a half an hour?


I'd expect to feel some stickiness in 5 mins or so, even with pretty old glue, and would give up after 10!

Epoxy was my other guess, but I've no experience with that - Brian Howard has explained all, and it sounds just as tricky to remove as I suspected. Fingers crossed for you.



These users thanked the author profchris for the post: Conor_Searl (Thu Dec 13, 2018 12:19 pm)
Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Thu Dec 13, 2018 12:19 pm 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
B. Howard wrote:
Stripper with MEC in it (BTW if you haven't heard the stuff with MEC is going bye bye from the stores next year...). will work but it will not be absolutely clean when done and vapors are deadly.


MEC? Are you familiar with this brand? There is no list of ingredients on the side...

Attachment:
IMG_0794 (002).JPG


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Dissolving old glue
PostPosted: Thu Dec 13, 2018 12:23 pm 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
profchris wrote:
I'd expect to feel some stickiness in 5 mins or so, even with pretty old glue, and would give up after 10!

Epoxy was my other guess, but I've no experience with that - Brian Howard has explained all, and it sounds just as tricky to remove as I suspected. Fingers crossed for you.


Yeah I spent a good 10-15 minutes on a couple small spots with both boiled water and cotton like you suggested, as well as a damp rag and soldering iron. It didn't even get a little tacky. And scraping with a razor just left little white scratches. It's seeming more and more like it might be epoxy. But I'll pick up some acetone and try that as well as the stripper I have at home and see if that gets me any where before resigning myself to scraping it all off.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 18 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com