Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Oct 31, 2024 6:57 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 17 posts ] 
Author Message
PostPosted: Tue Aug 01, 2017 9:31 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Feb 27, 2005 10:11 am
Posts: 2167
On a commission I am doing the customer picked this rosette:

It's the white mop and black mop

http://luthiersupply.com/125/832/produc ... uitar.html

I am assuming it is to be set in black epoxy to fill the voids.

They are showing it against a black background...

Do you think that will look good?

or will the black mop be "washed out" into the black epoxy?

Also will it look better with a black purfling around it or right against the spruce?


Top
 Profile  
 
PostPosted: Tue Aug 01, 2017 10:17 pm 
Offline
Cocobolo
Cocobolo

Joined: Mon Apr 14, 2008 3:20 am
Posts: 376
Location: Kapolei HI
First name: Aaron
Focus: Build
Status: Semi-pro
Black MOP is not actually black.

If it says to cut the channel wider and fill with black epoxy - you have to be comfortable with using colored epoxy against end grain spruce inside the channel. Purfling is one way to mitigate some issues.


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 2:15 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jan 22, 2010 9:59 pm
Posts: 3590
First name: Dennis
Last Name: Kincheloe
City: Kansas City
State: MO
Country: USA
Focus: Build
Status: Amateur
Probably best to go with the instructions on the web site. Black MOP shows fine against actual black due to the reflectivity, and in this case it's supposed to look like it's in a shadow anyway.

But you'll have to ask the customer how they want it. Technically it would be possible to inlay it directly into the spruce with no circular border, but if that's what they have in mind then you'll probably need to charge extra.


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 8:04 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Feb 27, 2005 10:11 am
Posts: 2167
Aaron O wrote:
Black MOP is not actually black.

If it says to cut the channel wider and fill with black epoxy - you have to be comfortable with using colored epoxy against end grain spruce inside the channel. Purfling is one way to mitigate some issues.


Yes, Aaron,-good point about the end grain. I am leaning toward some type of purfling-probably just a single black line so as not to takle away from the simplicity of the design.

Thanks


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 8:31 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Feb 27, 2005 10:11 am
Posts: 2167
DennisK wrote:
Probably best to go with the instructions on the web site. Black MOP shows fine against actual black due to the reflectivity, and in this case it's supposed to look like it's in a shadow anyway.

But you'll have to ask the customer how they want it. Technically it would be possible to inlay it directly into the spruce with no circular border, but if that's what they have in mind then you'll probably need to charge extra.



Dennis,

Thanks for the insight.

This customer is leaving the nitty gritty details up to me.

it is a "money is no object" commission so no need to charge extra.

A good friend of mine died and left me more than I would usually charge for this guitar, (to build it for her boyfriend) so I am getting paid handsomely for this one...........


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 12:38 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat May 17, 2008 1:11 pm
Posts: 2369
Location: Spokane, Washington
First name: Pat
Last Name: Foster
Country: USA
Focus: Build
Status: Semi-pro
Brad,

I think the black MOP would be stunning against the black infill. It won't jump out, but will glow when the light hits it. I think it will add a lot of depth.

You could experiment with the black epoxy against spruce end grain. In my limited experience, epoxy doesn't penetrate the way some other adhesives do.

Pat

_________________
formerly known around here as burbank
_________________

http://www.patfosterguitars.com


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 12:48 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue May 13, 2008 10:44 am
Posts: 6256
Location: Virginia
I have not had a problem with epoxy penetrating spruce either. It's rather thick and gloppy but I suppose the dye used to blacken the epoxy if not mixed in real well could. But I would guess a coat of shellac would mitigate that problem. The one thing any filler will do though is find any and every flaw in the routed out channel edge and fill that. Sometimes that's why you see little saw tooth filled marks. Sharp tools of course for that problem.

FWIW I like using charcoal and white glue for black mastik fills.


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 12:56 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7371
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
In my experience it is very difficult to get a good sharp line with black epoxy/spruce. I have tried and ended up re-routing and putting in a piece of purfling. Maybe my technique was not good enough idunno

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Wed Aug 02, 2017 4:38 pm 
Offline
Cocobolo
Cocobolo

Joined: Mon Apr 14, 2008 3:20 am
Posts: 376
Location: Kapolei HI
First name: Aaron
Focus: Build
Status: Semi-pro
Brad Goodman wrote:
Aaron O wrote:
Black MOP is not actually black.

If it says to cut the channel wider and fill with black epoxy - you have to be comfortable with using colored epoxy against end grain spruce inside the channel. Purfling is one way to mitigate some issues.


Yes, Aaron,-good point about the end grain. I am leaning toward some type of purfling-probably just a single black line so as not to takle away from the simplicity of the design.

Thanks

I just reread the description. Your idea of a single black line on the inside and outside will do fine, especially considering you'll be placing and glueing each piece individually.

BTW, this is not a simple design. Personally, I'd throw a bwb purfling in there like Andy describes - I think the lighter colored lines will make the rosette "pop" where it needs to. This will also allow you to "practice on scrap" and setup your spacing. In theory, you could glue up the actual rosette on a blank, cut/route it out (and route off the white purfling if you don't like it) and inlay the rosette into the actual channel as one piece.

That said, I think that design is just begging to be engraved to throw shadows between the pieces and add depth. Imo.


Top
 Profile  
 
PostPosted: Thu Aug 03, 2017 1:06 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Brad, I used that same rosette several years ago. It will probably look fine set in black epoxy. But, never being smart enough to do things the easy way, I made an ebony insert for the rosette and inlayed the pearl the old fashioned way. It was a PITA but did come out ok.
Attachment:
IMG_0160[2].jpg


You do not have the required permissions to view the files attached to this post.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Thu Aug 03, 2017 11:53 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Feb 27, 2005 10:11 am
Posts: 2167
Joe Beaver wrote:
Brad, I used that same rosette several years ago. It will probably look fine set in black epoxy. But, never being smart enough to do things the easy way, I made an ebony insert for the rosette and inlayed the pearl the old fashioned way. It was a PITA but did come out ok.
Attachment:
IMG_0160[2].jpg



Hi Joe,

That looks great! Looks like you have a .020 B/W/B purfling around it?

I think I am going for that look-except I am using the dyed epoxy......


Top
 Profile  
 
PostPosted: Thu Aug 03, 2017 3:06 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Brad, I didn't keep good records or even a good picture of the rosette. (It was a rush. I think I had it out the door in less than 4 weeks).

I blew up the best photo I had and my best guess is I used 10/20/10 BWB, but your aesthetic choices have always been excellent. Look forward to seeing the finished product.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Thu Aug 03, 2017 6:21 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Feb 27, 2005 10:11 am
Posts: 2167
Joe Beaver wrote:
Brad, I didn't keep good records or even a good picture of the rosette. (It was a rush. I think I had it out the door in less than 4 weeks).

I blew up the best photo I had and my best guess is I used 10/20/10 BWB, but your aesthetic choices have always been excellent. Look forward to seeing the finished product.


Thanks for the vote of confidence....

Are you saying you built (and finished ) a guitar in 4 weeks?

Could you please share something (anything) about your process?

I an trying to get my time down and on one of my models I am around 60 hrs.


Top
 Profile  
 
PostPosted: Thu Aug 03, 2017 10:35 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue May 13, 2008 10:44 am
Posts: 6256
Location: Virginia
Joe Beaver wrote:
Brad, I used that same rosette several years ago. It will probably look fine set in black epoxy. But, never being smart enough to do things the easy way, I made an ebony insert for the rosette and inlayed the pearl the old fashioned way. It was a PITA but did come out ok.
Attachment:
IMG_0160[2].jpg

Wow [:Y:]


Top
 Profile  
 
PostPosted: Fri Aug 04, 2017 12:00 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1702
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
Joe Beaver wrote:
Brad, I used that same rosette several years ago. It will probably look fine set in black epoxy. But, never being smart enough to do things the easy way, I made an ebony insert for the rosette and inlayed the pearl the old fashioned way. It was a PITA but did come out ok.


Joe, that does look nice, also I really like the simple oval fret board inlays.

_________________
http://www.Harvestmoonguitars.com


Top
 Profile  
 
PostPosted: Fri Aug 04, 2017 6:06 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Brad, yes sir, about four weeks. The only rest I got was when the paint was drying!

Actually, since I was on a tight schedule I did do several things differently. For one I bought all the inlays from Andy DePaul, John, I think that was his snowflake fretboard inlays. Buying those, plus the headstock and rosette inlays really speeded things up.

And I usually make up 3-4 neck blanks from time to time and I just happened to have one ready for this build.

Now that I think about it 4 weeks was probably slow for that guitar.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Wed Aug 23, 2017 10:37 am 
Offline
Walnut
Walnut

Joined: Sat Aug 30, 2008 7:40 am
Posts: 23
Location: North Carolina
First name: Alan
I installed a similar rosette on a guitar for my daughter several years ago. Hasn't seen much use lately, so it has plenty of dust on it!

Rosette was set in black epoxy with BWB purfling.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 17 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 40 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com