Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 6:35 am


All times are UTC - 5 hours


Forum rules


Same rules apply to all forums at the Luthiers Forum.




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Tenor Cigar Box Ukulele
PostPosted: Sun Jul 23, 2017 11:28 am 
Offline
Cocobolo
Cocobolo

Joined: Tue Mar 26, 2013 6:49 pm
Posts: 403
First name: Fred
City: Winnipeg
Country: Canada
Focus: Build
Status: Amateur
I have a brace on my right hand and I am more or less out of commission as far as building goes for a while. But I found myself in need of a uke and I figured the least effort would be to use a cigar box for the body and use a ready made bridge that came as a kit with nut saddle and tuners. So nothing fancy here, hope it sounds ok.


A 2"x3" stud as the neck, a couple of pieces for a top which I can not remember why I cut them. Not quartered, might actually help out in a small build like this.

Image

Run a router over the edges of the top using a square as a straight edge.

Image

Gluing up the top and 'linings'.

Image

X braced the top to get the maximum area vibrating, well at least in my mind.

Image

Roughing out the neck.

Image

Further on the neck and cut a piece of walnut for the fretboard.

Image

Bridge glued to the top, top to the box, how am I going to do the neck joint?

Image

Actually looks like it may work. Frets in.

Image

Finished the neck, glued the fretboard to the top, shimmed the neck joint with a wedge, who would have thought a cigar box would have been built with the sides at right angles? A coat of poly on everything. A recessed pocket for a screw through the neck into the neck block. I did say this was going to be a half-as build didn't I?

Image

Finish her up today.


Top
 Profile  
 
PostPosted: Sun Jul 23, 2017 8:19 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Mar 26, 2013 6:49 pm
Posts: 403
First name: Fred
City: Winnipeg
Country: Canada
Focus: Build
Status: Amateur
Actually sounds not bad. Screwed up on the tuner placement, oh well. What is worse is that they are all the same side, the two lower strings need to turn backwards as compared to the other set. Otherwise it sounds pretty good, easy to play.

Image



These users thanked the author printer2 for the post (total 2): Pmaj7 (Sun Jul 23, 2017 11:21 pm) • Imbler (Sun Jul 23, 2017 8:25 pm)
Top
 Profile  
 
PostPosted: Sat Sep 16, 2017 8:10 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Mar 26, 2013 6:49 pm
Posts: 403
First name: Fred
City: Winnipeg
Country: Canada
Focus: Build
Status: Amateur
A real one this time.


Building a uke for some people at work. The rest of the projects are pushed back in order of importance. One side bent, one to go.
Image

This was unplanned, using the other uke body as a temporary form so it holds its shape. Did not think I would make more than one I did not make any forms for this shape.
Image

Gluing the neck and tail block.
Image

Trimmed and looking good.
Image

Installing the linings.
Image

A nice piece that is an orphan guitar side, need to thin it down some.
Image


Thinned down, with some wings on it should make for a good top.
Image


The back already joined.
Image


Cutting the sound hole.
Image


Bracing the top.
Image


Bracing the back and adding a bits under the bridge area.
Image


Gluing the sides onto the top. The clamp is for insurance the sides do not bow. A spacer runs from the neck block to the tail block and with the clamp nothing moved when adding the weights. I find this faster and easier than using clamps.
Image


Glued on the back as well. Trimmed and almost ready for finish. Need to put a ring of wood in the sound hole in place of a rosette. Then with some sanding it is almost ready to go. Time to think of the neck.
Image


Top
 Profile  
 
PostPosted: Tue Sep 19, 2017 3:06 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Mon Jan 14, 2013 3:25 pm
Posts: 337
Location: Bozeman, MT
First name: Tony
Last Name: Thatcher
City: Bozeman
State: MT
Looks great!

_________________
Tony Thatcher
Bozeman, Montana


Top
 Profile  
 
PostPosted: Wed Sep 20, 2017 11:13 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3288
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
I like it!

The go-bars look really sprung and they are set up pointed end down. Have you ever had them slip off and stab through the top or back?

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Sun Sep 24, 2017 6:01 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Mar 26, 2013 6:49 pm
Posts: 403
First name: Fred
City: Winnipeg
Country: Canada
Focus: Build
Status: Amateur
bcombs510 wrote:
I like it!

The go-bars look really sprung and they are set up pointed end down. Have you ever had them slip off and stab through the top or back?


You mean like today, or just generally?


Top
 Profile  
 
PostPosted: Sun Sep 24, 2017 6:08 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3288
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
:( Sorry if that happened. I just noticed because I use the same fiberglass rods. I built an overhead board that has a grid of holes in it spaced every 1/2". I put the pointed end into the hole to keep it from skating and put the rubber tipped end on the workpiece.


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 16 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com