Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 6:50 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 29 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: Sun Feb 01, 2015 11:04 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
Image

Start with the template for the bracing layout. One for each model.

Image

Make a block with the x angle cut into it accurately.

Image

Use it on the mitre guage.

Image

Fetch 'Stick With Purposeful Lump' and clip onto mitre guage.

Image

Align it so the blade passes through the same spot every time (yes, took a while to grock that).

Image

Choose your spacer, made by smart people by measuring, and by trial and error by people like me. Masking tape shims are your friend.

Image

Butt your braces against Purposeful Lump and take a cut. My mitre gauge has slop in the channel, so I make sure to always press obliquely to the left so it runs at a constant distance.

Add spacer and take second pass. Then take out the spacer and nudge the braces a bit so the blade hits the center of the notch so the height is constant.

Image

Zippetty do dah, perfectly angled press fit x joint!

Image

Clip spacers back onto the Purposeful Lump and stow for next time.

Takes a bit of time to make the templates and angle block for each model, but saves futzing about every time you make your x's...short term loss for long term gain.



These users thanked the author meddlingfool for the post (total 3): Clinchriver (Tue Oct 24, 2017 5:55 pm) • ernie (Tue Oct 24, 2017 12:40 pm) • Terence Kennedy (Sun Feb 01, 2015 11:36 pm)
Top
 Profile  
 
PostPosted: Sun Feb 01, 2015 11:47 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2422
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
Dang, now I need a table saw.

You know that you're now going to have to file for trademarks on " Super Simple Speedy Sunday X Brace Notching System" and "Purposeful Lump".

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter


Top
 Profile  
 
PostPosted: Sun Feb 01, 2015 11:50 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
I don't mind sharing.... :)

I find my tablesaw very useful. It's a Bosch job site style, retails these days for around 600$. We also bought a second DeWalt one about a year ago for 300$, and it's awesome too.



These users thanked the author meddlingfool for the post: Bri (Mon Feb 02, 2015 9:48 am)
Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 12:04 am 
Offline
Koa
Koa
User avatar

Joined: Mon Sep 05, 2011 10:45 pm
Posts: 1470
First name: Trevor
Last Name: Gore
City: Sydney
Country: Australia
Focus: Build
Status: Professional
J De Rocher wrote:
Dang, now I need a table saw.

Only if you really want one.

The same idea will work on a router table. I use a similar sort of fixture for making lattices on a router table.

_________________
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.

http://www.goreguitars.com.au



These users thanked the author Trevor Gore for the post: J De Rocher (Mon Feb 02, 2015 1:27 am)
Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 12:14 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
I know my tablesaw sees a lot of use. Enough to buy one for each end of the shop...


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 3:00 am 
Offline
Mahogany
Mahogany
User avatar

Joined: Tue Nov 11, 2008 5:36 pm
Posts: 68
First name: Edzard
Last Name: Kolks
City: Eindhoven
Country: The Netherlands
Focus: Build
Nice!

This will do the trick too:
http://www.bridgecitytools.com/default/ ... maker.html


Regards,


Edzard


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 5:34 am 
Offline
Koa
Koa

Joined: Sun Jul 26, 2009 9:37 am
Posts: 697
First name: Murray
Last Name: MacLeod
City: Edinburgh
Country: UK
Good job, but why don't you have a length of birch ply permanently screwed on to the miter gauge to act as a cross-cut fence?


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 6:04 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7240
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Nicely done. You might consider an Incra fence. It can be adjusted to fit the table saw channel without slop and is also more easily set for the angles.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 7:22 am 
Offline
Koa
Koa

Joined: Sat May 19, 2007 11:03 am
Posts: 1737
Location: Litchfield MI
Focus: Build
Status: Professional
Here's an adjustable "X"notch jig that does not require power tools -- just a razor saw.

http://www.kennethmichaelguitars.com/Xb ... guide.html

_________________
Ken Cierp

http://www.kennethmichaelguitars.com/


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 7:36 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Mar 01, 2011 1:32 pm
Posts: 3470
First name: Alex
Last Name: Kleon
City: Whitby
State: Ontario
Zip/Postal Code: L1N8X2
Country: Canada
Focus: Build
Status: Amateur
Thanks for sharing that, Ed. If I can make one suggestion, though - make a zero clearance insert for each of your table saws! You'll get cleaner cuts on the bottom side of the wood, and off cuts won't get caught or ping back at you! Great terminology, as well. Now all I have to do is find a mitre gauge for my 1" mitre slot. [headinwall]

Alex

_________________
"Indecision is the key to flexibility" .... Bumper sticker


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 7:48 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Jun 04, 2007 3:31 am
Posts: 904
Location: Candler, NC United States
Great idea. You can take the slop out of your miter gauge by pinging the sides with a spring punch.


Ken Jones
Mountain Song Guitars

_________________
Mountain Song Guitars www.mountainsongguitars.com


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 10:01 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
Good job, but why don't you have a length of birch ply permanently screwed on to the miter gauge to act as a cross-cut fence?

Haven't found the need as of yet...


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 10:03 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
I have one for a different gadget that I'm workiing on, maybe I'll give it a try. The slop in the runner is real easy to account for by making sure the bar runs against the edge...


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 10:05 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
make a zero clearance insert for each of your table saws! You'll get cleaner cuts on the bottom side of the wood, and off cuts won't get caught or ping back at you!

I have them for some tasks, like when using the fretsaw blade for cutting purflings...


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 6:14 pm 
Offline
Contributing Member
Contributing Member

Joined: Sat Feb 19, 2011 7:44 pm
Posts: 1225
Location: Andersonville
State: Tennessee
Country: USA
Focus: Build
Status: Professional
meddlingfool wrote:
I know my tablesaw sees a lot of use. Enough to buy one for each end of the shop...


Tablesaw good :mrgreen:

Thats pretty much how I do it, I've just been creeping up on the width but the spacer is a nice addition


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 7:03 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
This is one of the jobs that is very satisfying with a fine toothed back saw and a chisel - a great skill to have. Kind of like learning to grind and sharpen your edge tools without a jig. Much quicker than locating the jig, setting it up, etc.

And Ken's little jig is a nice addition.

Ed


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 7:51 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Nov 16, 2007 8:36 am
Posts: 114
Location: United States
First name: kurt
Last Name: thomas
City: colden
State: ny
Zip/Postal Code: 14033
Status: Amateur
Maybe a dumb question, but the spacer needs to be the exact thickness of the braces, correct? And.. the depth of the cut is right at half the height of the brace(s). This looks much better than my hammer and flat screwdriver method.

_________________
_____________________________

Kurt Thomas

"There's a first time for everything even if you do it by mistake."


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 8:33 pm 
Offline
Contributing Member
Contributing Member

Joined: Sat Feb 19, 2011 7:44 pm
Posts: 1225
Location: Andersonville
State: Tennessee
Country: USA
Focus: Build
Status: Professional
KThomas wrote:
Maybe a dumb question, but the spacer needs to be the exact thickness of the braces, correct? And.. the depth of the cut is right at half the height of the brace(s). This looks much better than my hammer and flat screwdriver method.


I'd like to hear Ed's take on this also, I like a tight press fit, thumb and finger tight so mine would be a few thousandths under. And yes on 1/2 the height.


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 9:57 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
I personally go a little past halfway as there is still the bottom radius to be shaped. So about .010 extra, which leaves you a bit of wiggle room to put in your radius.

The combined width of your blade and spacer should be the width of your brace., minus a few thou for a tight press fit. I think...I made mine via trial and error...


Top
 Profile  
 
PostPosted: Mon Feb 02, 2015 10:20 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3289
Location: Alexandria MN
You can also cut them just a little tight and sand a few thou off the sides of the brace with a hard sanding block to fine tune a squeek fit.
I've used a router jig I copied from Charlie Hoffman for the last 10 years but I like this saw thing, lots quicker to set up.
Thanks!

_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.


Top
 Profile  
 
PostPosted: Tue Feb 03, 2015 1:25 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Good stuff Ed. I like the way you think.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Tue Feb 03, 2015 1:37 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
The way I think is to make things as simple and easily repeatable as possible with the minimal amount of thought required so I don't have to stand there and go, 'Hmm, how's that go again?'...


Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 11:48 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Jan 31, 2009 8:50 pm
Posts: 2246
Location: Seattle WA
Focus: Build
Status: Semi-pro
meddlingfool wrote:
The way I think is to make things as simple and easily repeatable as possible with the minimal amount of thought required so I don't have to stand there and go, 'Hmm, how's that go again?'...
No kidding! I was standing there looking at this really cool sweet jig that I made going, "Hmm....I wonder what this is for..." I'm going to start writing more notes on them.

_________________
Pat


Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 11:58 am 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Mon Jan 14, 2013 3:25 pm
Posts: 337
Location: Bozeman, MT
First name: Tony
Last Name: Thatcher
City: Bozeman
State: MT
Slick! But my table saw is currently a fancy base for my home made drum sander and buffer. It takes more time to change back to table saw mode than it does to use my razor saw. But I love the simplicity and repeatability of the setup!

_________________
Tony Thatcher
Bozeman, Montana


Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 12:14 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
Now I use a dado blade instead of a regular blade and spacer.

I use my Laguna bandsaw for basically all my straight cuts now, so the tablesaw has he dado in full time and is used for only two jobs, x brace joints and truss rod slots which use the same blade.

I cut the x's now just a hair thick and then sand them to about .005 oversized on the drum sander for a nice tight fit.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 29 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: Brad Goodman and 56 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com