Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sat Jul 19, 2025 6:29 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 10 posts ] 
Author Message
 Post subject: X-Brace
PostPosted: Sat Nov 08, 2008 1:41 am 
Offline
Walnut
Walnut
User avatar

Joined: Wed Oct 01, 2008 11:38 am
Posts: 27
Location: Campobello, S.C.
Does everybody cut their x-braces to a certain degree or do you cut it differant for each guitar?

_________________
We Bend the Wood, So You Can Bend the Strings


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 1:47 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Jan 04, 2005 10:03 am
Posts: 6680
Location: Abbotsford, BC Canada
I always position my bridge first when laying out the internals (I draw everything on the inside first). Then I make sure my xbrace runs over the wings of the bridge. I also like to make the front of my xbrace about 1-1/2" to 1-3/4" from the back edge of the sound hole. So, I really don't think about the angle too much, just make sure they cover the wings of the bridge.

_________________
My Facebook Guitar Page

"There's really no wrong way, as long as the results are what's desired." Charles Fox

"We have to constantly remind ourselves what we're doing....No Luthier is putting a man on the moon!" Harry Fleishman

"Generosity is always different in the eye of the person who didn't receive anything, but who wanted some." Waddy Thomson


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 3:47 am 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
I do the same as Rod. The angle isnt critical but having the braces run under the ends of the bridge is important.


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 10:08 am 
Offline
Contributing Member
Contributing Member

Joined: Mon Jan 03, 2005 7:46 am
Posts: 1315
Location: Branson, MO
First name: stan
Last Name: thomison
City: branson
State: mo
Zip/Postal Code: 65616
Country: united states
Focus: Build
Status: Professional
Like others I know where bridge/bridge plate is going first. If that (bridge placement) gets messed up, well then one is for lots of other issues that are not fun. I use to mess with the angle of the braces, and then set the plate to fit.

I do the bridge plate as the first thing glued in. I then do the upper transverse brace. I started this from way did it at Bourgeois and worked well no matter what model made. I know where the top is going to meet the neck in join and can set the bridge plate from there depending on 12 or 14 fret, and soon going into making a batch of 13 fret to body. The angle of the plate ends allow me about 90 degree's +/-, I never have looked at it with a protractor or whatever do that with. I just leave's a good distance for soundhole braces and where upper ends of the X ends. From there it is placing and gluing the rest and whittling them down. I note though, I use vacuum to glue down the braces, so easier to do the bridge plate first. For me just faster to place all of the braces at one time and not mess with the sticks.


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 1:16 pm 
Offline
Koa
Koa
User avatar

Joined: Sat Aug 19, 2006 1:29 am
Posts: 1384
Location: United States
On my last few I have run the unbraced thicknessed top through the chladni testing and drawn the shapes on the underside of the top. I have found that many of these patterns cross right where the normal Martin style bracing crosses at the x-brace, upper tone bar and finger brace area. I have been using this point and the wings of the bridge to set the angle. Not surprisingly, most of the traditional Martin bracing matches up well to main points of intersection or strong Chladni lines on the unbraced top. The only spot where there hasnt been (also keep in mind, very small tesing group) too much of a clue is the lower tone bar. Also not surprisingly, this area seems to be where most of my attention is paid in trying to close the circle. But, for the X that is how I am doing it. It hasn't been far off where I would normally put it (i.e. close to 90 degrees).

_________________
Burton
http://www.legeytinstruments.com
Brookline, MA.


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 2:12 pm 
Offline
Walnut
Walnut

Joined: Sat Oct 11, 2008 11:16 am
Posts: 5
Do you consider the stiffness of the top when arranging your x-brace? How should top stiffness effect brace placement, or is it not a consideration?


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 2:16 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Wed Oct 08, 2008 12:06 pm
Posts: 169
I was wondering how critical it is to have the braces running right under the bridge posts for an archtop. Is this an absolute rule that should never be broken? In the Benedetto book, for an X-Brace he shows it varying. However, for a parallel brace he has them directly under the posts. I've read about a lot of luthiers experimenting with X-Brace positioning so I would be surprised if they have to stay exactly under the bridge posts all the time.


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Sat Nov 08, 2008 2:44 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Sep 09, 2005 7:51 am
Posts: 3786
Location: Canada
I use 98 for most guitars, likely pretty close to what Martins are .. Laskins and Larrivee's use 90 for everything except basses if they still make them. For baritones, I end up at 90 because the brigde has moved back intothe lower bout.

_________________
Tony Karol
www.karol-guitars.com
"let my passion .. fulfill yours"


Top
 Profile  
 
 Post subject: Re: X-Brace
PostPosted: Wed Nov 12, 2008 8:47 am 
Offline
Walnut
Walnut
User avatar

Joined: Wed Oct 01, 2008 11:38 am
Posts: 27
Location: Campobello, S.C.
Thanks Guys, the reason I asked was because I saw where some of you were making x-braces in batches, so I figured you had a pre-determend degree.

_________________
We Bend the Wood, So You Can Bend the Strings


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 22 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com