Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 6:46 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Vacuum Clamping Bridges
PostPosted: Tue Mar 20, 2018 11:38 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Nov 12, 2014 10:02 am
Posts: 513
First name: Daniel
Last Name: Petrzelka
State: Washington
Country: United States
Focus: Build
I finally had a chance to try a vacuum bridge clamp - a whole new world.

LMII vacuum bridge clamp with a GAST DOA-P707-AA (FleaBay Score) pulling 24-25 in of Hg with a good seal. I also tried it with an older GAST DOA-101 and it worked equally well. The local Semi-truck repair shop had some really nice all brass 1/8" NPT to 1/8 tube quick connects that are wonderful. They allow the use of the more flexible 1/8" hose/tube, and look like they should last forever.

With the vacuum pump/clamp I'm able to apply glue, and have it clamped in 25 seconds or less - allowing me time to use hot hide glue up to 315g strength—which is way, way more than I have any need for, but its possible. I've always had success with the standard 162g hide glue from Behlen.

Hesh, I'm sure you'll have some thoughts ;) - but I'm having fun over here.

Image

Image

Image

Image





You can see a little Instagram video of it in action here:
https://www.instagram.com/p/BgeLrT4guNZ/?taken-by=dpetrzelka




Ken had posted a great piece over at http://www.acousticguitarconstructionforum.com/ about making your own vacuum clamp for bridges here:

DIY Bridge Vacuum Clamp
http://acousticguitarconstructionforum.com/viewtopic.php?f=7&t=817




...


Top
 Profile  
 
PostPosted: Mon Mar 26, 2018 5:57 pm 
Offline
Cocobolo
Cocobolo

Joined: Sat Dec 28, 2013 10:06 am
Posts: 251
First name: Mike
Last Name: Spector
City: ORANGE
State: TX
Zip/Postal Code: 77632
Country: USA
Focus: Build
Status: Amateur
I'm interested in either making or buying a small vacuum clamp setup. How long do you leave the rig running after setting it on the bridge?


Top
 Profile  
 
PostPosted: Mon Mar 26, 2018 6:13 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Nov 12, 2014 10:02 am
Posts: 513
First name: Daniel
Last Name: Petrzelka
State: Washington
Country: United States
Focus: Build
I'm only getting started with this vacuum clamp—So take this as only one approach, but it's working so far.

For hot hide glue, 192g and 315g are the two I've tried, I vacuum clamp for 10-15 minutes, then clean up squeeze out.
I then clamp again for a minimum of 45min-1hr. After that I let they dry overnight before stringing up.

In the hide glue cure time thread some debate started about the efficacy of vacuum clamping bridges and usage with hide glue. Lots of opinions. So far I've had success, but can't speak to first hand experience with longevity of the glue-up. I have no reason to suspect it will fail vs a traditionally clamped bridge with a hide glued joint.

Robbie O'Brien talks briefly about it this Tips du Jour video

https://www.youtube.com/watch?v=9FTG5p2dsBA

https://www.youtube.com/watch?v=qRqCp1zKOEk

He is using a Titebond style glue I believe, but maybe he can weigh in on HHG usage?


Top
 Profile  
 
PostPosted: Tue Mar 27, 2018 10:14 pm 
Offline
Koa
Koa

Joined: Mon Oct 17, 2011 4:10 pm
Posts: 634
First name: Bob
Last Name: Gramann
City: Fredericksburg
State: VA
Zip/Postal Code: 22408
Country: USA
Focus: Build
Status: Professional
I’ve been vacuum clamping my bridges for several years now. I preheat the bridge to extend my working time. Usually about five minutes after I apply the clamp, I remove it and clean up the squeezeout. After that, I clamp it for another 2 hours (or more depending on when I can get back to turn off the pump). I wait to string it up until the next day whether I use 192g or 315g glue (I haven’t had a bridge pop since I started using 315g).

I started using the vacuum clamp because I had problems with bridges distorting under clamping pressure some times. The vacuum clamp applies pressure about as evenly as can be done. And it sure is easier than setting internal and external cauls and three through the soundhole clamps.



These users thanked the author bobgramann for the post: dpetrzelka (Wed Mar 28, 2018 9:10 am)
Top
 Profile  
 
PostPosted: Sun Apr 01, 2018 12:12 pm 
Offline
Cocobolo
Cocobolo

Joined: Sat Dec 28, 2013 10:06 am
Posts: 251
First name: Mike
Last Name: Spector
City: ORANGE
State: TX
Zip/Postal Code: 77632
Country: USA
Focus: Build
Status: Amateur
I'm used to cutting the saddle slot before I glue on the bridge. Does the vacuum pull down without moving the bridge ? It almost looks like you could recheck the slot measurements even with the thing pulling down.


Top
 Profile  
 
PostPosted: Sun Apr 01, 2018 4:29 pm 
Offline
Koa
Koa

Joined: Mon Oct 17, 2011 4:10 pm
Posts: 634
First name: Bob
Last Name: Gramann
City: Fredericksburg
State: VA
Zip/Postal Code: 22408
Country: USA
Focus: Build
Status: Professional
I locate the bridge, drill the two outer holes, and hold it in position with the StewMac slick tapered pins. Personally, I wouldn’t expect the bridge to stay exactly where I left it with any clamping system unless it was pinned.


Top
 Profile  
 
PostPosted: Sun Apr 01, 2018 4:49 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Nov 12, 2014 10:02 am
Posts: 513
First name: Daniel
Last Name: Petrzelka
State: Washington
Country: United States
Focus: Build
I pin mine as well - either as Bob described above for replacement bridges or with small metal pins through the saddle slot


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com