Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Mon Nov 09, 2026 7:17 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Sun Oct 25, 2026 8:59 pm 
Offline
Walnut
Walnut

Joined: Wed Apr 09, 2025 1:25 am
Posts: 4
First name: Bernard
Last Name: Boulanger
City: Vancouver
State: British Columbia
Zip/Postal Code: V7G 2T8
Country: Canada
Focus: Repair
Status: Amateur
HI , for fun I recently picked up a project 50s Kay K1. It's a jumbo archtop with a solid, likely pressed spruce top and laminate maple back and sides.
It has some top cracks, a loose brace, a terrible refinish done by a 4 year old apparently, needs refret, and needs a new bridge carved etc.
My plan is to have fun repairing what needs to be repaired see how it sounds acoustically and if it doesn't excite me acoustically, maybe maybe add pickups or sell it as is but functional and looking better.
I realize this a low level archtop (despite the solid pressed top) and my investment isn't huge so the stakes are low.
I've had and worked on several higher quality acoustic archops, flattops, and generally play vintage ply archops live which I also work on

I took the back off so I could fix the brace which was dislodged from an impact and that worked out well. There's still a few cracks to stabilize.

My questions are: Is it worth tuning the top at all on these guitars?
The braces aren't huge. At the bridge they stand around 11/16 - 7/8 high ,and are slightly over 5/16 wide so despite the height, quite narrow.
They are quite rough with the top corners slightly rounded, When I say tuning the top I mean via the shaping the braces not thinning the top

Also it has quite large plates in the inside of the F-holes which I understand the rationale for but I'm tempted to thin them out some near the edges, taper them into the top more and remove some material.
Is it worth doing this?
I was maybe going to bind the F-holes (which I've done before and enjoy doing) lightly.

I have a picture but can't seem to post it. I choose it, I add it , I get an uploading bar and then it refreshes the screen and nothing


Last edited by Toxophilite on Mon Oct 26, 2026 10:03 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Mon Oct 26, 2026 11:52 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Nov 04, 2010 1:46 pm
Posts: 2211
First name: Freeman
Last Name: Keller
Focus: Build
Status: Amateur
I would be interested in seeing the photo(s) altho I probably won't be much help. The usual reason for the upload to fail is that the photo it too big, forum software wants pretty small files.

I've built a few laminated guitars, one carved acoustic archtop and worked on a few more (including installing a pickup on a high end archtop). When I built my carved guitar I did a lot of voicing, mostly trying to learn what I was hearing. I can at least comment on yours.


Top
 Profile  
 
PostPosted: Mon Oct 26, 2026 10:04 pm 
Offline
Walnut
Walnut

Joined: Wed Apr 09, 2025 1:25 am
Posts: 4
First name: Bernard
Last Name: Boulanger
City: Vancouver
State: British Columbia
Zip/Postal Code: V7G 2T8
Country: Canada
Focus: Repair
Status: Amateur
Do you know what size is too big? I just a bit shrinking and shrinking the photo with no luck


Top
 Profile  
 
PostPosted: Tue Oct 27, 2026 12:08 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jan 11, 2013 2:26 pm
Posts: 531
First name: Carl
Last Name: Dickinson
City: Forest Ranch
State: California
Zip/Postal Code: 95942
Country: USA
Focus: Build
Status: Amateur
File sizes over 150kB are probably too big.


Top
 Profile  
 
PostPosted: Tue Oct 27, 2026 12:14 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Nov 04, 2010 1:46 pm
Posts: 2211
First name: Freeman
Last Name: Keller
Focus: Build
Status: Amateur
"The file is too big, maximum allowed size is 256 KiB."

Its always been an issue with forum software. Other forums don't have this limit. I find that when I want to post a picture from my phone or camera I have to open it with Paint, resize it to 20 percent, save under a new name, then go thru the rigamarole of adding and inserting.


Top
 Profile  
 
PostPosted: Tue Oct 27, 2026 12:18 pm 
Offline
Walnut
Walnut

Joined: Wed Apr 09, 2025 1:25 am
Posts: 4
First name: Bernard
Last Name: Boulanger
City: Vancouver
State: British Columbia
Zip/Postal Code: V7G 2T8
Country: Canada
Focus: Repair
Status: Amateur
Thanks that's very helpful here is a 234kb picture of the interior


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Wed Oct 28, 2026 11:47 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Nov 04, 2010 1:46 pm
Posts: 2211
First name: Freeman
Last Name: Keller
Focus: Build
Status: Amateur
I'm the last person that should be commenting on this but what I see does not surprise me. As I'm sure you know, there are basically two ways to brace an acoustic archtop, X braced and "parallel" braced which is what you have. In theory they have different voices, I chose X for the one I built.

Benedetto calls parallel braces out at 5/16 wide and 5/8 to 1/2 tall under the bridge, tapering to 1/8 or so at the ends. So yours don't look that unreasonable.

As I understand f-holes they have two functions - tuning the air chamber resonance and weakening the top at its very outside edge. Yours have been reinforced since that is an area where splits occur. Binding them will make their cross section smaller, I like to bind mine to match body and head binding.

One thought would be to try to rebuild this as closely as possible to what Kay did originally, put it back together and see if you like its voice. If you don't you can always add a floating pickup mounted on the pickguard or the end of the fretboard, that way you don't compromise the acoustic voice. I've installed a couple of floating pickups for jazz playing friends and they have been quite happy.

The last comment is that when I build my archtop and the occasions where I have modified something like you are considering I have used some audio spectrum software to chart the changes, it lets me try to understand what I think I'm hearing as I make the changes. I talked about here in a build thread that I did for another forum, again this is my amateur way of trying to understand what Benedetto describes in his book.

Go to post #180 at the bottom of page 9

https://www.tdpri.com/threads/lets-buil ... t-11098796

Now I'll shut up and wait for the folks that know what they are talking about to chime in.


Top
 Profile  
 
PostPosted: Thu Oct 29, 2026 11:15 pm 
Offline
Walnut
Walnut

Joined: Wed Apr 09, 2025 1:25 am
Posts: 4
First name: Bernard
Last Name: Boulanger
City: Vancouver
State: British Columbia
Zip/Postal Code: V7G 2T8
Country: Canada
Focus: Repair
Status: Amateur
Thanks for the Bendetto specs, that's good to know. As this is supposed to be a pressed top I would imagine it doesn't have as much inherent structural strength as a carved top so perhaps a little more height to the braces might be a necessity. I was contemplating lightly scalloping them away from the area the bridge sits on, and scalloping the top edges and leaving the height.

I don't know if Kay spent a lot of time voicing or tuning their tops. the braces are very rough and not sanded. The wooden F-hole backing plates are unevenly applied differing by as much as 1/4" in their location around the F-holes. etc. etc. The whole thing has the appearance of a hastily assembled inexpensive factory instrument. The solid top is the best thing it has going for it.
If nothing else I'd like to make it look a little more like someone cared amd perhaps open up the sound a little.

I have about 5 cracks glued up, some bigger than others, all solid, some prettier than others. I took the braces down a little on either side of the bridge and rounded them. Knocked the doorskin cleats a previous repair used to a more reasonable height. These used the guitar string tuner fix. It seems pretty resonant now. It had a few definite dead spots. The treble side rings a little higher, maybe B while the bass side is closer to G#


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com