Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 11:22 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 36 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Ed's Build.
PostPosted: Tue Jan 08, 2013 3:45 pm 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
Right, after searching through the big thread in the other forum, I have decided to enter. I have completed 2 already, and half started No.3, but had to stop because of a move. I plan on keeping that build shelved until this one is complete (if this is breaking the rules let me know and I will pull out of the contest).

I have been watching the last challenge with great interest and vowed that I would join in on the fun of the next contest. Didn't think it would come round so fast but, lets get it on!

Build #3 details:
While in limbo of moving I had no shop time, so I started designing my own guitar (2 actually, 1 small bodied and a large bodied). I have never used CAD so I went the old fashioned route: pencil, paper, coloured cardboard, scissors and sellotape. Photos of these to-scale cardboard cut outs to come later.

For this challenge I am going to make the Lge bodied design I have come up with.

S/B - Spruce (Engleman I think)
B/S - EIR
Neck - Mahogany - I have some Brazilian mahogany but I'm not sure if I will use it for this build.

Will decide on the other elements later on.

I hope this thread will be as entertaining and inspiring to you all as much as the ones in the last challenge. Good luck to all who enter, and I look forward to following everyone's progress.

Ed.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Tue Jan 08, 2013 7:42 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Jul 27, 2009 7:52 am
Posts: 4524
First name: Big
Last Name: Jim
State: Deep in the heart of Bluegrass
Country: usa
Focus: Build
Status: Amateur
Nope , your good for this contest as far as Im concerned ! Looking forward to seeing the build [:Y:]

_________________
The Shallower the depth of the stream , The Louder the Babble !
The Taking Of Offense Is the Life Course Of The Stupid One !
Wanna Leave a Better Planet for our Kids? How about Working on BETTER KIDS for our Planet !
Forgiveness is the ability to accept an apology that you will probably NEVER GET
The truth will set you free , But FIRST, it will probably Piss you Off !
Creativity is allowing yourself to make Mistakes, Art is knowing which ones to Keep !
The Saddest thing anyone can do , is push a Loyal Person to the point that they Dont Care Anymore
Never met a STRONG person who had an EASY past !
http://wiksnwudwerks.blogspot.com/
http://www.facebook.com/groups/GatewayA ... rAssembly/


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Wed Jan 09, 2013 4:44 pm 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
Thanks Wud for confirming.

Been cleaning up the back set and have one plate thicknessed. Will take progress shots at the weekend.

Some dimensions of the guitar :geek: :

Scale Length = 650mm

Body
Neck Block to Tail Block = 20"
Lower Bout = 16.5"
Upper Bout = 12"
Waist = 10"

Body Depth
@ Neck Block = 100mm
@ Tail Block = 120mm

Neck Width

@ Nut = 46mm
@ Body = 56mm

Will hopefully have a hand stop, probably not a slotted headstock. Will be scarf joint with a stacked heel.

Have been thinking about fret board, bridge, head plate and bindings. I might try to keep this project to 3 types of wood. Using EIR for b/s, f/b, bridge and head plate; mahogany bindings, neck, linings, and back bracing; spruce top and s/b bracing.

I am also considering radial purfling using EIR, and EIR for the rosette.

EIR over-kill? Or a simple celebration of this wood?

Has anyone used Mahog for bindings? Do you think it will complement the EIR well?

Comments and suggestions always welcome.

Thanks

Ed.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Wed Jan 09, 2013 5:06 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur
Hey Ed. Just curious, why are your body dimensions in inches yet all others are metric? idunno


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Wed Jan 09, 2013 5:46 pm 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
I use metric for when I need to be acurate and imperial for rough measurements.

Hope that helps.

Ed.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Wed Jan 09, 2013 6:00 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Over here in England we are just unitally confused! laughing6-hehe
mm are so much easier to use, but there are some things that just work better in inches.

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Wed Jan 09, 2013 6:35 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur
Everything is better in inches. One day you will all see. Metric is for the birds beehive


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 1:18 am 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
What I don't get about imperial is, when should you use fractions off an inch, and when to use a decimal of an inch?


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 5:16 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 17, 2012 6:14 am
Posts: 195
First name: Brad
City: St. Louis
State: MO
Country: USA
Focus: Build
Most of us just make it up as we go :P

_________________
Brad


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 9:01 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Oct 12, 2010 9:01 pm
Posts: 3031
First name: Tony
Last Name: C
City: Brooklyn
State: NY
Focus: Build
Status: Amateur
There is only one thing I measure in metric, and I wont be posting a pic of it. laughing6-hehe

_________________
http://www.CostaGuitars.com
PMoMC


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 9:22 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Mar 01, 2011 1:32 pm
Posts: 3470
First name: Alex
Last Name: Kleon
City: Whitby
State: Ontario
Zip/Postal Code: L1N8X2
Country: Canada
Focus: Build
Status: Amateur
Tony_in_NYC wrote:
There is only one thing I measure in metric, and I wont be posting a pic of it. laughing6-hehe

wow7-eyes wow7-eyes wow7-eyes

Alex

_________________
"Indecision is the key to flexibility" .... Bumper sticker


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 9:23 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Oct 07, 2010 5:28 pm
Posts: 687
First name: Casey
Last Name: Cochran
City: Gainesville
State: GA
Zip/Postal Code: 30501
Country: USA
Focus: Build
Tony_in_NYC wrote:
There is only one thing I measure in metric, and I wont be posting a pic of it. laughing6-hehe


Now, that's funny.

_________________
Good judgement comes from experience. Experience comes from poor judgement.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 9:32 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur
Hastings Guitars wrote:
What I don't get about imperial is, when should you use fractions off an inch, and when to use a decimal of an inch?


Generally fractions are used for dimensions and measurements that have loose tolerances +/- 1/64 or more. Decimals though are used in precision work. Anything with close tolerances are measured in thousandths of an inch. In manufacturing thousandths is the standard measurement. For instance if you have .01 most anyone who has much experience in manufacturing will not call that "one hundredth" of and inch, they will refer to it as "ten thousandths". Just as .0002 would be called "two tenths of a thousandth".

Fractions are much more commonly used by construction workers and welders where precision is usually not a factor. Machinists more commonly use decimals.

I hope that made sense.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 9:57 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Mar 01, 2011 1:32 pm
Posts: 3470
First name: Alex
Last Name: Kleon
City: Whitby
State: Ontario
Zip/Postal Code: L1N8X2
Country: Canada
Focus: Build
Status: Amateur
Attachment:
ruler.jpg
ZekeM wrote:
Hastings Guitars wrote:
What I don't get about imperial is, when should you use fractions off an inch, and when to use a decimal of an inch?


Generally fractions are used for dimensions and measurements that have loose tolerances +/- 1/64 or more. Decimals though are used in precision work. Anything with close tolerances are measured in thousandths of an inch. In manufacturing thousandths is the standard measurement. For instance if you have .01 most anyone who has much experience in manufacturing will not call that "one hundredth" of and inch, they will refer to it as "ten thousandths". Just as .0002 would be called "two tenths of a thousandth".

Fractions are much more commonly used by construction workers and welders where precision is usually not a factor. Machinists more commonly use decimals.

I hope that made sense.
Does this mean I have to replace my ruler to build a guitar?

Alex


You do not have the required permissions to view the files attached to this post.

_________________
"Indecision is the key to flexibility" .... Bumper sticker


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Thu Jan 10, 2013 10:36 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur
well alex that just depends on the accuracy you will require. if you are going fretless then i dont see any reason why you couldnt just use a ruler. it would be easier with more a more precise ruler but hey if you build your entire guitar and the only measuring instrument you use is that ruler, well then if it plays good and sounds good ill vote for you. that would impress me very much. :D


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Sun Jan 13, 2013 11:06 am 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
Thanks guys for the clarity on the imperial stuff. May try it one day.

Went to get the camera out yesterday and the battery has died, so its phone pics only for a while.

Back jointed, thickened and rough shaped.
Attachment:
Back.jpg


Sides with one side cleaned up.
Attachment:
Sides.jpg


When thickening one of the sides, I had a little split [headinwall]. I should be able to get away with it though, as there is plenty of width in the wood for the side.
Attachment:
Side break.jpg


Neck Blank pre clean-up
Attachment:
Neck Blank.jpg


Mapping the scarf cut
Attachment:
Map Scarf.jpg


Gluing the scarf joint
Attachment:
Glue Scarf.jpg



I will take some pics of my cardboard mock-up later and try to post it for you all to laugh at.

Thanks

Ed


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Sun Jan 13, 2013 2:17 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur
Looking good Ed. I wouldnt worry too much about that split, it looks like you are still wider than you will need. That is if you arent going extra deep with it. I know I make mine 4.125'' at the tail and 3.5'' at the neck, so for me you got plenty to work with.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Mon Jan 14, 2013 3:52 pm 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
Thanks Zeke, I agree. I think I have plenty in width especially if i make that end at the head block. Also I think I have an extra 3-4" in length so I may just chop it off. We will see.

Work is looking busy this week (that coupled with the snow that has covered the UK), I dont think I will get any shop time until the weekend :(

Ed


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Mon Jan 14, 2013 4:55 pm 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
I have drawn out plans and I have also made a cardboard mock-up to have a better idea of what it will look like. Also with the mock up you can place it on your knee and pretend its a real guitar bliss .

Attachment:
Cardboard cut out.jpg


The tap tone of this cardboard rings like a bell laughing6-hehe

Let the mockery begin Eat Drink

Ed


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Mon Jan 14, 2013 5:01 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Oct 07, 2010 5:28 pm
Posts: 687
First name: Casey
Last Name: Cochran
City: Gainesville
State: GA
Zip/Postal Code: 30501
Country: USA
Focus: Build
Hastings Guitars wrote:
I have drawn out plans and I have also made a cardboard mock-up to have a better idea of what it will look like. Also with the mock up you can place it on your knee and pretend its a real guitar bliss .

Attachment:
Cardboard cut out.jpg


The tap tone of this cardboard rings like a bell laughing6-hehe

Let the mockery begin Eat Drink

Ed



It's a little thin, isn't it? laughing6-hehe

_________________
Good judgement comes from experience. Experience comes from poor judgement.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Mon Jan 14, 2013 5:29 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Nice fretboard inlays! laughing6-hehe

Alex Kleon wrote:
Does this mean I have to replace my ruler to build a guitar?

Alex


Measure with a micrometer,
Mark with chalk,
Cut with an axe! :mrgreen:

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Tue Jan 15, 2013 3:18 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Jan 05, 2005 6:25 pm
Posts: 2749
Location: Netherlands
Or just become fluent in both; I think of my body 'large' dimensions in inches (16" lower bout, 25.5" scale length) and smaller dimensions in millimeters (45mm nut width, 1.8 or 2mm side thickness, and so forth). Since I hang out at US forums, it's sort of a requirement. Have to say that any time I actually measure something I do it in mm, even though my calipers and all my rules are marked in both metric and imperial (and the rules have handy conversion tables for common decimal inches engraved on the back. Cheap steel rules from Axminster.co.uk in various sizes, very handy)


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Tue Jan 15, 2013 3:58 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Oct 28, 2012 2:04 am
Posts: 92
First name: William
Last Name: Holmwood
City: Brighton
Country: England
Focus: Build
I'm trying to get into the habit of using both metric and imperial. metric is fine, unless you need to divide something by three..


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Sun Jan 20, 2013 4:00 am 
Offline
Mahogany
Mahogany

Joined: Thu Nov 17, 2011 12:23 pm
Posts: 64
First name: Ed
Country: England
Focus: Build
Status: Amateur
Even though we have 2" of snow and half the country shut down :roll: , I managed to battle my way up to my workshop yesterday. Made some progress with the neck and the sound board.

Attachment:
Heel blocks ready to glue.jpg


And a shot all glued up:

Attachment:
Glueing stacked heel..jpg


Cleaned up the sound board plates :

Attachment:
Cleaning up 1 of the sb plates.jpg


Thicknessed by hand, have thought about thickness sanders but nothing wrong with a little elbow grease and a hand plane. Could always do with extra exercise pizza

Attachment:
Thcknessing the sb plate.jpg

Took the plates down to 3mm. Am going to leave them stickered and stacked up for a couple of weeks under weight (noticed a slight bit of cupping as I was taking them down) to settle before jointing them. Then I will get the sound board to final thickness.

Oh and I have made a template (on top of the cardboard cut-out)

Attachment:
template.jpg



As always opinions, comments and suggestions welcome.

Thanks

Ed


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Ed's Build.
PostPosted: Tue Jan 22, 2013 11:03 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7241
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Hastings Guitars wrote:
What I don't get about imperial is, when should you use fractions off an inch, and when to use a decimal of an inch?


Use fractions if you're working with a measuring tape. Use decimals if you're using a caliper. As one who uses both systems I am comfortable with fractions but they are less convenient to manipulate ;)

Looks like you're making good progress.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 36 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: Bing [Bot] and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com