Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 5:04 am


All times are UTC - 5 hours





Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 10 posts ] 
Author Message
PostPosted: Sat Jan 28, 2012 3:36 am 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 23, 2008 8:05 pm
Posts: 1567
Location: San Jose, CA
First name: Dave
Last Name: Fifield
City: San Jose
State: CA
Zip/Postal Code: 95124
Country: USA
Focus: Build
Status: Amateur
My entry is going to be a bit of an experiment. I am going to build an OLF-SJ size/shape guitar that has a "triple top" (sitka/sitka/sitka with a laser-cut honeycombed center) made from 3 of Shane's 2A specials. The back and sides will be local claro walnut.

I will post photos and build progress reports periodically. 8-)

Cheers
Dave F.

_________________
Cambrian Guitars

"There goes Mister Tic-Tac out the back with some bric-brac from the knick-knack rack"


Top
 Profile  
 
PostPosted: Sat Jan 28, 2012 3:51 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Aug 18, 2005 2:21 am
Posts: 2924
Location: Changes when ever I move..Australia
Focus: Build
Status: Amateur
Wow..will be watch'in this one with great intrest Dave...go get'em [:Y:]

Cheers

Kim


Top
 Profile  
 
PostPosted: Sat Jan 28, 2012 9:11 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Tue Oct 14, 2008 11:06 am
Posts: 372
curious to know why?
no bracing?


Top
 Profile  
 
PostPosted: Sun Jan 29, 2012 4:12 am 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 23, 2008 8:05 pm
Posts: 1567
Location: San Jose, CA
First name: Dave
Last Name: Fifield
City: San Jose
State: CA
Zip/Postal Code: 95124
Country: USA
Focus: Build
Status: Amateur
Thanks Kim! [:Y:]

Steve - it's the asymtote of increasing the soundboard stiffness while reducing the bracing size (yes, no bracing)....the honeycomb laminated triple-top came out more than stiff enough, and is much lighter than a "standard" top with my normal fair-curved X-bracing. All being well, this guitar could end up sounding great (or completely horrible)....we'll see....

The honeycomb center section of the top:
Image

The finished top (notice the runout...but at $10 a top, I can't complain!):
Image

The edge of the top, showing the three layers:
Image

The claro walnut back/sides slab prior to jointing and resawing:
Image

The sides being resawed:
Image

I got 4 guitars worth of lovely flame/figured back and sides sets out of the slab, plus a lot of spare (good for boxes, pens, etc.):
Image

Cheers for now,
Dave F.

_________________
Cambrian Guitars

"There goes Mister Tic-Tac out the back with some bric-brac from the knick-knack rack"


Last edited by Dave Fifield on Sun Jan 29, 2012 10:03 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Sun Jan 29, 2012 11:37 am 
Offline
Koa
Koa

Joined: Tue Jul 04, 2006 3:24 am
Posts: 744
Location: United States
Dave...very interesting. I built a double top last year and often thought about doing something similar to what you are doing. What are the thicknesses of the triple top layers?

_________________
Brad
Avon, OH


Top
 Profile  
 
PostPosted: Sun Jan 29, 2012 5:03 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue May 02, 2006 9:02 am
Posts: 2351
Location: Canada
First name: Bob
Last Name: Garrish
City: Toronto
State: Ontario
Country: Canada
Status: Professional
That's some slick work there!

How long did that thing take to laser out and what method did you use to join the laminates?

_________________
Bob Garrish
Former Canonized Purveyor of Fine CNC Luthier Services


Top
 Profile  
 
PostPosted: Sun Jan 29, 2012 9:59 pm 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 23, 2008 8:05 pm
Posts: 1567
Location: San Jose, CA
First name: Dave
Last Name: Fifield
City: San Jose
State: CA
Zip/Postal Code: 95124
Country: USA
Focus: Build
Status: Amateur
Brad - the center honeycomb piece is 0.085" thick, and the two outer pieces are 0.065" thick, for a total thickness of 0.215"....right now, that is.....I plan on thinning it a bit once the box is closed (especially around the edges), depending on how it taps and the deflection I see at the brige. The glued-up soundboard is 0.25" over-size all the way around (gotta leave some for routing after the top is glued to the sides) - this is quite a lot of extra weight that is going to disappear. If the technique works, I will build more instruments the same way and experiment with the stiffness to weight ratio in a more scientific manner.

Bob - I found that vector cutting didn't really work very well, the probem being that the little hexagonal pieces don't just fall out, but get in the way and cause cut errors (the vector grid stops many of them, but others seem to pop up and get in the cutting field. I ended up raster engraving it (using 100% power at a fairly slow speed). It takes many hours to do....I'm running one right now - it's been going for 2 hours and it's only just getting up to the wide part of the lower bout (it started at the bottom of the guitar = bottom-up engraving)....it's probably going to be another 3 hours yet! I'm going to try vector cutting the next one but with it raised up on a bed of strategically placed pins - should be about 30-40 minutes. That way, the little hexagons should fall out the bottom as they are cut and not get in the way.....we'll see. I used ordinary LMI Luthier's Glue to glue the three pieces together. I used glue sparingly and rollered it out thin. I glued all three pieces together at once, using a 28' dish in a vacuum press. It seems to keep its shape nicely.

I've been trimming the bookmatched walnut back wood, jointing them, and gluing them together this afternoon.....piccies later.

Cheers,
Dave F.

_________________
Cambrian Guitars

"There goes Mister Tic-Tac out the back with some bric-brac from the knick-knack rack"


Top
 Profile  
 
PostPosted: Wed Mar 14, 2012 10:16 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 05, 2005 3:45 pm
Posts: 4337
Location: United States
Dave, that honeycombed top is almost unbelievable. (But there it is, right before me eyes....)
Don't be slamming the shop doors with one of those lying around in its unglued state!
In fact, don't sneeze or even curse too loudly. Looks really fragile.

(I just know I'd break it right before glue up time.)

Steve

_________________
From Nacogdoches...the oldest town in Texas.

http://www.stephenkinnaird.com


Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 9:06 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Jul 27, 2009 7:52 am
Posts: 4524
First name: Big
Last Name: Jim
State: Deep in the heart of Bluegrass
Country: usa
Focus: Build
Status: Amateur
This is a very interesting Build . I am glad we have the build threads so that we can watch this one being built !! [:Y:]

_________________
The Shallower the depth of the stream , The Louder the Babble !
The Taking Of Offense Is the Life Course Of The Stupid One !
Wanna Leave a Better Planet for our Kids? How about Working on BETTER KIDS for our Planet !
Forgiveness is the ability to accept an apology that you will probably NEVER GET
The truth will set you free , But FIRST, it will probably Piss you Off !
Creativity is allowing yourself to make Mistakes, Art is knowing which ones to Keep !
The Saddest thing anyone can do , is push a Loyal Person to the point that they Dont Care Anymore
Never met a STRONG person who had an EASY past !
http://wiksnwudwerks.blogspot.com/
http://www.facebook.com/groups/GatewayA ... rAssembly/


Top
 Profile  
 
PostPosted: Thu Mar 15, 2012 5:01 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Jan 05, 2005 6:25 pm
Posts: 2749
Location: Netherlands
Very curious to hear the results on this one...


Top
 Profile  
 
Display posts from previous:  Sort by  
Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 10 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com