Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 9:38 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Sun Aug 25, 2013 8:04 am 
Offline
Mahogany
Mahogany

Joined: Tue Jun 26, 2012 2:35 am
Posts: 90
First name: Lee
Last Name: Passmoor
City: Newport Pagnell
State: Bucks
Zip/Postal Code: MK16 8JG
Country: United Kingdom
Focus: Build
Status: Amateur
Hi, I am hoping you fine folk can give me a bit of advice!

I am about to start a build using black limba for the back and sides. I am sanding the sides to thickness and notice I have a worm hole in it. This comes to approximately where the cutaway section would be. It is a venetian cutaway and the hole will land at around the sharp external bend. I did consider turning the wood around so the hole was at the lower bout, but the figuring of the wood suits this orientation better.

My question is should I do anything with the hole before I start bending (using a hot pipe), and if so what should I do? Fill with CA? Epoxy? or just leave it as is and fill with a shellac stick when finishing? I guess I am worried that the hole will lead to a crack when bending.

Hopefully this photo will come out OK!
Image

Any advice would be greatly appreciated.

Lee


Top
 Profile  
 
PostPosted: Sun Aug 25, 2013 2:37 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jun 26, 2012 2:35 am
Posts: 90
First name: Lee
Last Name: Passmoor
City: Newport Pagnell
State: Bucks
Zip/Postal Code: MK16 8JG
Country: United Kingdom
Focus: Build
Status: Amateur
Filippo Morelli wrote:
CA and dust.

Filippo


Thanks Filippo. Should I do this before I bend it?


Top
 Profile  
 
PostPosted: Sun Aug 25, 2013 3:04 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Oct 12, 2010 9:01 pm
Posts: 3031
First name: Tony
Last Name: C
City: Brooklyn
State: NY
Focus: Build
Status: Amateur
I had many worm holes in my black limba and I did nothing to them. It's wood, and imperfections like this should be admired, not hidden in my opinion. But, z-poxy will work fine. As will CA and dust. Plus, if the worm holes resulted in orange steaks, it's great to show them to people and explain how the worms caused the orange with their worm poop.

_________________
http://www.CostaGuitars.com
PMoMC


Top
 Profile  
 
PostPosted: Sun Aug 25, 2013 3:07 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jan 22, 2010 9:59 pm
Posts: 3552
First name: Dennis
Last Name: Kincheloe
City: Kansas City
State: MO
Country: USA
Focus: Build
Status: Amateur
If you did a pointy cutaway, could you get it where the wormhole would be right at the tip, so it will be eliminated in the process of cutting the miter?


Top
 Profile  
 
PostPosted: Sun Aug 25, 2013 4:12 pm 
Offline
Koa
Koa
User avatar

Joined: Thu Feb 21, 2008 8:57 pm
Posts: 1982
Location: 8.33±0.35 kpc from Galactic center, 20 light-years above the equatorial in the Sol System
First name: duh
Last Name: Padma
City: Professional Sawdust Maker
Focus: Build
Bend with metal slats to avoid worm hole blow out.
Fill after.

If you do get blow out, it can usually be glued and clamped back down with culls.

_________________
.

Audiences and dispensations on Thursdays ~ by appointment only.



.


Top
 Profile  
 
PostPosted: Sun Sep 01, 2013 4:23 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jun 26, 2012 2:35 am
Posts: 90
First name: Lee
Last Name: Passmoor
City: Newport Pagnell
State: Bucks
Zip/Postal Code: MK16 8JG
Country: United Kingdom
Focus: Build
Status: Amateur
Thanks for the replies. As an update I decided to bend without filling as I was worried that a hardened fill would lead to an increased likelihood of inducing a fracture. Everything went well as can be seen here and I will probably go with an epoxy/dust fill when finishing.
Image
Image

Again, thanks for the replies.


Top
 Profile  
 
PostPosted: Tue Oct 01, 2013 10:48 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Jan 27, 2008 4:10 pm
Posts: 2764
First name: Tom
Last Name: West
State: Nova Scotia
Country: Canada
Focus: Build
Status: Amateur
Small sound port.............!!!
Tom

_________________
A person who has never made a mistake has never made anything!!!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com