Official Luthiers Forum!

Solely owned and operated by Lance Kragenbrink
It is currently Sat Nov 18, 2017 5:16 am


All times are UTC - 5 hours


Forum rules


Same rules apply to all forums at the Luthiers Forum.




Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Sat Apr 01, 2017 8:39 pm 
Offline
Koa
Koa
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 797
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Recently I picked up the fret tang remover from Jescar along with some narrow wire for ukes. I had the opportunity to fret two boards with it today. Generally speaking it's a nice tool and easy to use. The two problems I did have were with the wire being already radiused and with the guide on the tool itself.

The wire was radiused to 16" to match the board. I was using the #1 guide attachment. The wire would get slightly kinked right at the inside edge of the cut area because the wire was radiused and not sitting flat in the guide for the full width. I also noticed that the guide was just slightly bigger than the wire so I would have to adjust the wire a bit on each cut to get a clean shave off of just the tang.

Doing some test cuts I had significantly better and consistent results with flat wire.

Some questions:

1) Is it common to put the fretboard on flat? This would make the job a lot easier with the nipper.

2) Is it common to use the thinnest jescar wire or do you guys like to use medium guitar wire instead to make jumbo Uke wire?

3) Anyone have experience with this cutter and can lend some technique advice or confirm what I'm experiencing?

Thanks!
Brad


Sent from my iPhone using Tapatalk

_________________
"Is this the one where I trot downfield and act like I'm lost ?" - Billy Bob


Top
 Profile  
 
PostPosted: Sat Apr 01, 2017 10:45 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Nov 11, 2008 9:13 pm
Posts: 772
Location: Durango CO
First name: Dave
Last Name: Farmer
City: Durango
State: CO
http://luthiersforum.com/forum/viewtopic.php?f=10101&t=48050&hilit=fret+nippers

The search for the perfect nipper goes on.
The Jescars at least seem to handle stainless. Every time I use them I think about grinding off 75% of the shelf to accommodate wire radius better. It's a lot of hard steel to remove and so far I haven't taken the time. My stew macs just won't fit really big wire.

Never met a tool I didn't need to modify. idunno



These users thanked the author david farmer for the post: bcombs510 (Sun Apr 02, 2017 3:29 pm)
Top
 Profile  
 
PostPosted: Sat Apr 01, 2017 11:14 pm 
Offline
Cocobolo
Cocobolo

Joined: Mon Apr 14, 2008 3:20 am
Posts: 228
Location: Kapolei HI
First name: Aaron
Focus: Build
Status: Semi-pro
The smallest radius I've done is 20", which is enough to piss you off, but also enough for the player to feel. I've done it once. No comment on radiusing ukulele fretboards, and moreso doing a bound one with small fretwire that no current nipper exists. There are other ways to trim fretwire, but that's another thread.

I use the equivalent of StewMac 147 on my tenors. No issues with the Hosco nipper, and certainly none when I stepped up to the Summit. I do use the 764 for recent Tiples, and had the expected issues of trimming smaller wire.

Note: even though my fretboards are flat, I radius the wire.

Add 1: Radiused fretboards on ukulele are the exception, and not the norm, and you'll see custom builders do it, but the factories don't (except customs, I'm sure)


Last edited by Aaron O on Mon Apr 03, 2017 12:57 pm, edited 1 time in total.


These users thanked the author Aaron O for the post: bcombs510 (Sun Apr 02, 2017 3:30 pm)
Top
 Profile  
 
PostPosted: Sun Apr 02, 2017 2:50 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Dec 01, 2006 6:44 pm
Posts: 437
Location: Australia
First name: Allen
Last Name: McFarlen
City: Mt. Sheridan
State: Qld.
Zip/Postal Code: 4868
Country: Australia
Focus: Build
Status: Professional
My fret boards are a 12" - 16" compound radius. I use them on SM #764wire that has been rolled. My binding is just 2mm and I only try to nip just over 2mm on that wire. Any more and it doesn't work to well.

_________________
Allen R. McFarlen
Barron River Guitars & Ukuleles
Facebook
Cairns, Australia



These users thanked the author Allen McFarlen for the post: bcombs510 (Sun Apr 02, 2017 3:30 pm)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com