Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 5:04 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Mon Mar 26, 2018 3:11 pm 
Offline
Walnut
Walnut

Joined: Mon Mar 26, 2018 12:15 am
Posts: 2
First name: Ronald
Last Name: Fairfax
City: El Segundo
State: CA
Zip/Postal Code: 90245
Country: USA
Focus: Repair
Status: Amateur
I'm replacing the stock tremolo in my Ibanez Js100 with a Gotoh Floyd rose, however the posts for the Gotoh are slightly larger. I was going to use the existing posts, but then decided I should probably try to install the Gotoh posts, as the old posts are slightly worn. I'm going to have to drill the holes slightly larger to accommodate the Gotoh posts. Is there anything I should be aware of before embarking on this potentially disastrous repair? My plan is to drill with a slightly larger metric drill bit, then hammer in the new posts and hope for the best. Getting pretty excited to upgrade my JS100! Thanks for your help, amigos!


Top
 Profile  
 
PostPosted: Mon Mar 26, 2018 4:35 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
I've done this a lot recently.... Get the proper size metric drill bit, go slowly keeping it absolutely perpendicular, and push them in with your thumb. Tapping with a wooden block is acceptable if they are a little tight. If you hammer them you deserve everything bad that will befall you.

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Mon Mar 26, 2018 5:04 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Aug 19, 2005 4:02 am
Posts: 3227
Location: The Woodlands, Texas
First name: Barry
Last Name: Daniels
Are you drilling the holes with a drill press?


Top
 Profile  
 
PostPosted: Mon Mar 26, 2018 10:38 pm 
Offline
Walnut
Walnut

Joined: Mon Mar 26, 2018 12:15 am
Posts: 2
First name: Ronald
Last Name: Fairfax
City: El Segundo
State: CA
Zip/Postal Code: 90245
Country: USA
Focus: Repair
Status: Amateur
Thanks for the tips, Pile!

Barry, I was going to use a handheld drill and try my best to stay perpendicular, but now that you mention it, a press would really be the tool for the job. Might be time to call up some carpenter friends and see what I have access to.


Top
 Profile  
 
PostPosted: Mon Mar 26, 2018 11:44 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
The JS model is pretty curvy, so keep it stable....

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Tue Mar 27, 2018 10:52 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Nov 04, 2010 1:46 pm
Posts: 2124
First name: Freeman
Last Name: Keller
Focus: Build
Status: Amateur
JettyRatt wrote:
Thanks for the tips, Pile!

Barry, I was going to use a handheld drill and try my best to stay perpendicular, but now that you mention it, a press would really be the tool for the job. Might be time to call up some carpenter friends and see what I have access to.


Altho the quill of a drill press isn't really designed for it I have used them to press studs (and tuner bushings). Chuck a piece of dowel in it, support the body the same way you did when you drilled the holes.

Also if you are worried about centering the holes, plug the old ones with a piece of dowel and mark the centers, then drill with the correct brad point bit.



These users thanked the author Freeman for the post: dpetrzelka (Wed Mar 28, 2018 9:25 am)
Top
 Profile  
 
PostPosted: Sat Mar 31, 2018 6:48 am 
Offline
Contributing Member
Contributing Member

Joined: Sat Feb 19, 2011 7:44 pm
Posts: 1225
Location: Andersonville
State: Tennessee
Country: USA
Focus: Build
Status: Professional
JettyRatt wrote:
I'm replacing the stock tremolo in my Ibanez Js100 with a Gotoh Floyd rose, however the posts for the Gotoh are slightly larger. I was going to use the existing posts, but then decided I should probably try to install the Gotoh posts, as the old posts are slightly worn. I'm going to have to drill the holes slightly larger to accommodate the Gotoh posts. Is there anything I should be aware of before embarking on this potentially disastrous repair? My plan is to drill with a slightly larger metric drill bit, then hammer in the new posts and hope for the best. Getting pretty excited to upgrade my JS100! Thanks for your help, amigos!



Everyone is giving you good advice, especially drilling with the right size bit, I just had to do a repair on a home Gotoh Floyd install the the owner was pressing in the new bushings with a vice :mrgreen: You might want to do a test fit on some scrap.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com