Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Mar 29, 2024 12:49 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Thu Sep 23, 2010 1:46 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Dec 05, 2009 3:51 pm
Posts: 1201
First name: Chris
Last Name: Ensor
City: Springfield
State: Missouri
Focus: Build
Status: Professional
I saw a post recently on bridge making jigs and I thought I would post about how I construct mine. I make pinless bridge, which means they are a little more complicated- or at least my design is.

I first setup my fence on my router table with stops- making sure they are equidistant from the bit. I use a 1/8" downcut spiral bit to route the saddle slot. After testing on scrap, I move on to the blank. In order to achieve the angle of the saddle slot, I attach a 4 mm square on the treble end of the blank. This is important. Carefully lower the blank into the bit and slowly feed it through until you reach the other block. I then hold the blank in that position and turn off the router. I only remove the blank once I am certain the bit has come to a complete stop.

I then draw the center line on the blank- referencing the saddle slot- not the length of the blank itself. I line up that center line with the center line on my master bridge template.

I then rough out the shape on the bandsaw- get close to the line so my router doesn't have to do much work later.

I line up the roughed out bridges center line with the center line on my routing template. The bridge is held on by double stick tape and two toggle clamps.

I then route using a bottom bearing bit to follow the template. I also leave in my adjustment wrench to use as a starting pin. It is essential that you route carefully- never route uphill on the grain. If you do- the last picture will show you what the result will be.


You do not have the required permissions to view the files attached to this post.

_________________
ELEVATE || Next Level Lutherie
http://elevatelutherie.com
&
http://ensorguitars.com


Top
 Profile  
 
PostPosted: Thu Sep 23, 2010 1:54 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Dec 05, 2009 3:51 pm
Posts: 1201
First name: Chris
Last Name: Ensor
City: Springfield
State: Missouri
Focus: Build
Status: Professional
After the bridge has been shaped, I transfer the center line to the front edge. I also mark the outside of the saddle on the top and the front- no real reason- I just like to. I then mark a line 4mm from the bottom of the bridge blank of the front side. This is where the bottom of the string holes will hit.

I then use my drilling jig to drill the holes. The jig consists of a moveable plate that sets the angle of the drill and a spacing template that is held in place with toggle clamps. Line up the drilling template so the it is centered with the bridge blank. I make sure that the saddle side of the bridge is parallel to the plexi drilling template. This is important. But more important is that the show face is against the adjustment plate- otherwise your strings will be coming out of the bottom of the bridge. I then drill with the corresponding bits.

The blank is now ready for carving and final fit and sand. Here is what mine looks like all done.

And as promised- the final picture is what happens when you route uphill on the grain.

Thanks for reading!


You do not have the required permissions to view the files attached to this post.

_________________
ELEVATE || Next Level Lutherie
http://elevatelutherie.com
&
http://ensorguitars.com


Top
 Profile  
 
PostPosted: Thu Sep 30, 2010 7:47 pm 
Offline
Walnut
Walnut

Joined: Sat Jul 18, 2009 1:58 pm
Posts: 4
City: Brunswick
State: Maine
Focus: Build
Status: Amateur
Thanks for sharing!


Top
 Profile  
 
PostPosted: Mon Jun 25, 2012 8:20 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Oct 12, 2010 9:01 pm
Posts: 3031
First name: Tony
Last Name: C
City: Brooklyn
State: NY
Focus: Build
Status: Amateur
This tutorial is much better than the one done by Tony in NYC!

_________________
http://www.CostaGuitars.com
PMoMC


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com