Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 12:34 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 24 posts ] 
Author Message
 Post subject:
PostPosted: Tue Jan 01, 2008 9:22 am 
Offline
Koa
Koa

Joined: Tue Jul 04, 2006 3:24 am
Posts: 744
Location: United States
A while ago I made the mistake and watched the Taylor Guitars Factory Friday video on the side bending. If you have not seen this then you must check it out! I was amazed by the way Taylor was able to bend sides and reduce the number of variables to just one. They only vary the bending speed (slow and fast) and everything else is the same for all woods! Of course I am sure that the Taylors benders cost big $$$ so at first it didn't seem possible building a bender similar to theirs.

After some thought I did figure out how I could use many of the concepts Taylor used without fully automating the process like they do.

So here is my side bending process that uses many of the same principles as Taylor. Please note that this project was lots of work and by no means is a quick fix to making a better bender. My goal was the design a better process. If your goal is to build guitars then just build a Fox or Doolin and get to work. If you enjoy designing and building a better process than you may find this interesting.

Before I start here are a couple facts that I picked up in my research on bending wood that I think are worth noting:

1) Heating or steaming wood radically changes its compression properties but has no effect on its tensile properties. What I gained from this is that if heat is applied to the inside of a bend it will be most effective..this also ties into what Taylor does.

2) Heating dry wood will create moisture but since the wood will dry out quickly using this approach it is important to only apply heat to the areas that are being bent and not the entire piece of wood.

3) Using stainless steel slats under tension helps keep the wood from breaking at the outside of the bend... the point where the wood is highly stressed (tensile) from the bending process.

I will walk though the steps and hopefully you will get the idea.

Sample Walnut, .102 thick


Wrap in kraft paper



Bender is heated to 280-300 degress AND then the wood is loaded into the bender. I only want to heat the wood when I am bending to not dry it out.


At this point I support the upper arm of the bender, hook the lower slat with the upper slat and apply 40 psi to the air cylinders to pull the slats in tension.


I bend the upper arm back which creates about 75% of the waist bend.


Keep in mind that I have a 5 x 6 heating blanket at the waist caul to just heat the waist.


Bending the lower bout.


I now tighten two clamp knobs that brings the waist in tight with the form.


Bird's eye view. Ready to bend the upper bout.


Bend the upper bout.


Let the wood cook for a few minutes (still working on how long)


I release the pressure on the air cylinders and un-hook the lower slat from the the upper slat.


I return the bender arms to the original upright position. This leaves the bent wood on the mold which can easily be removed and the process started over for the next side.


Ahhh....a newly bend side. (I have the side clamped between my table saw fence so it looks like there is no spring back but there is some)


Since the sides are bent dry they don't cup, distort, or discolor.


I am still working out the details but so far I have bent about 10 sides for testing and the results are very good. I even bent a curly maple side at about .120 thick just to push it and it had two small cracks in the waist.

Maybe this will inspire a few new thoughts on side bending.

And no...I don't plan to make these for resale.

_________________
Brad
Avon, OH


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 9:35 am 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat May 13, 2006 4:05 am
Posts: 337
Location: Reno, Nevada
First name: Michael
Last Name: Hammond
Focus: Build
Status: Amateur
    THIS is good stuff!

_________________
The Biggest Little City, Nevada
www.hammondguitars.com
I love building guitars!


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 9:54 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Dec 03, 2005 10:04 am
Posts: 2060
Very very nice system there. I'm impressed.

_________________
Eschew obfuscation, espouse elucidation.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 10:16 am 
Offline
Cocobolo
Cocobolo

Joined: Sun Jul 15, 2007 5:01 am
Posts: 140
Location: United Kingdom
wow i am very impressed i would think that there would real commercial
oppertunitys with this design i hope you have put a patent on it.

i would love to see someone make a comercial version of this.

well done

joel.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 10:50 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
When it the lift-off for the Mars mission.....

Brad I am really glad that you are not a terrorist.......

This is yet another over the top, very innovative - high-tech jig from you - WOW!!!!

Is the keypad on the side keyless entry.......


_________________
Ann Arbor Guitars


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 10:58 am 
Offline
Koa
Koa

Joined: Wed Jun 01, 2005 6:35 am
Posts: 1325
Location: Kings Mtn., NC, USA
First name: Bill
Last Name: Greene
City: Kings Mountain
State: North Carolina
Zip/Postal Code: 28086
Country: USA
Focus: Build
Status: Amateur
This is the coolest thing I've ever seen.

_________________
Eagles may soar, but weasels don't get sucked into jet engines.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 11:12 am 
Offline
Koa
Koa

Joined: Tue Jul 04, 2006 3:24 am
Posts: 744
Location: United States
[Quote=Hesh]Is the keypad on the side keyless entry[/QUOTE]

Actually I was trying to figure out how to make thing work with a "Remote Starter".


_________________
Brad
Avon, OH


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 11:21 am 
Offline
Koa
Koa

Joined: Sat Aug 04, 2007 10:37 am
Posts: 590
Location: United States
First name: Michael
Last Name: Shaw
City: Phila
State: PA
Zip/Postal Code: 19125
Country: United States
Yes this a very interesting post. Thanks

_________________
Guitars, guitars and more guitars.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 11:34 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Mar 01, 2007 3:15 pm
Posts: 2302
Location: Florida

Outstanding device Brad! I cant wait to see the final version. You may have stumbled on something that will help all of us build better guitars.


The fact that the sides dont have any stain, warp or cupping is proof enough that you are really onto something good here.


THANKS!!


_________________
Reguards,

Ken H


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 11:44 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Jul 28, 2007 1:03 pm
Posts: 724
Location: NE Oklahoma, United States
First name: Steve
Last Name: Walden
City: Bartlesville
State: Oklahoma
Zip/Postal Code: 74006
Country: USA
Focus: Build
Status: Amateur

That is really neat!     .......I can't believe I said neat........


Brad - Very innovative.  Can you give us a ball park as to the amount you have spent on this?  TIA


_________________
Steve Walden
Aspiring Builder,
Bartlesville, OK


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 11:59 am 
Offline
Koa
Koa

Joined: Tue Jul 04, 2006 3:24 am
Posts: 744
Location: United States
[Quote=WaldenWorx]Can you give us a ball park as to the amount you have spent on this?[/QUOTE]

Good questions? Well are some of the expenses....

1" Steel for frame, $50
Air Cylinders $10 ea. (Ebay)
Fittings for Pnumatics, $40
Temp Controller, Relay, Electronics, $100
Waist Blanket $35
Mold Blanket (Already had it $75)
Stainless Slats $25 (Ebay)
Misc. Bolts, Wood, $100?

Hard to really say the final cost. Many of the parts were from scrap so I didn't have to buy. Ebay is also a really great place to find surplus stuff at a greatly reduced cost.

_________________
Brad
Avon, OH


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 12:53 pm 
Offline
Contributing Member
Contributing Member

Joined: Mon Dec 27, 2004 11:25 pm
Posts: 7195
Location: United States
Umm....yeah, too bad you went so simple with that little jig...




Nice work!


_________________
"I want to know what kind of pickups Vince Gill uses in his Tele, because if I had those, as good of a player as I am, I'm sure I could make it sound like that.
Only badly."


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 1:55 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Nov 16, 2007 8:36 am
Posts: 114
Location: United States
First name: kurt
Last Name: thomas
City: colden
State: ny
Zip/Postal Code: 14033
Status: Amateur

Brad,


Yours is NICER than Taylor's.


_________________
_____________________________

Kurt Thomas

"There's a first time for everything even if you do it by mistake."


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 2:32 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4777
This is really cool, Brad. In premise, it seems like a Doolin bender, but
you've taken it a step further to pre-bend the waist. I'm really impressed
by the thinking that went into making this, getting each bend in exactly
the right place, etc. Thanks for posting this.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 3:23 pm 
Offline
Mahogany
Mahogany

Joined: Sat Nov 10, 2007 11:55 am
Posts: 68
Location: United States

Wow!!! I don't know what to say...You really oughta patent that- very ingenious!   I'll bet you were the kid that everybody wanted to peek over the shoulder of during science exams!


Thanks for sharing!


   



Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 4:28 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
That is a really impressive process.  Your ingenuity shines in the design of your bender.   I really like the inside heat thingy for the waist bend.  Nice touch.  Does the fact that you are heating from both sides on the waist bend have any impact on the process?

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 8:50 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue May 02, 2006 9:02 am
Posts: 2351
Location: Canada
First name: Bob
Last Name: Garrish
City: Toronto
State: Ontario
Country: Canada
Status: Professional
Here's my next project, for sure. The way you executed it is just beautiful.

_________________
Bob Garrish
Former Canonized Purveyor of Fine CNC Luthier Services


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 10:39 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Jan 12, 2007 11:47 pm
Posts: 153
Location: United States
First name: Vincent
Last Name: Simokovich
City: Parma
State: OH
Zip/Postal Code: 44134
Country: USA
Focus: Build
Status: Amateur
Hey Brad that walnut looks familiar! Nice job.

Vince


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 01, 2008 11:44 pm 
Offline
Koa
Koa

Joined: Tue Jul 04, 2006 3:24 am
Posts: 744
Location: United States
[Quote=WaddyT]Does the fact that you are heating from both sides on the waist bend have any impact on the process?[/QUOTE]

I am not sure that heating from both sides causes any problems. My original design used 2 blankets that were pressed against the wood on the inside of the slats. After some testing I found that all the extra heat just dried the wood out quicker and didn't really help the process. However, this is for bending dry. If I had spritzed the wood the extra heat would probably create more steam which could help the process.

[Quote=vinman]Hey Brad that walnut looks familiar[/QUOTE]
It sure does...all the extra mismatched sides really have worked out great for testing. Thanks for the wood!

_________________
Brad
Avon, OH


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 02, 2008 12:23 am 
Offline
Mahogany
Mahogany

Joined: Fri Nov 30, 2007 1:57 am
Posts: 97
Location: East Granby, CT

Geez MacGuyver, what's your toaster look like? 


Very nice - How do you find time to dream up stuff like this?  Air Cylinders?  I'm still sweating at the palms at carving my first neck! Got anything for that?  a pneumatic carver built from leftover lawnmower parts, maybe? 


totally ingenious....you really ought to patent it. 


Mitch



Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 02, 2008 12:49 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3289
Location: Alexandria MN
Jaw dropping totally industrial rig Brad.  Wow!  Does it make latte?
Terry


_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 02, 2008 1:42 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Jun 22, 2005 10:11 am
Posts: 2761
Location: Tampa Bay
First name: Dave
Last Name: Anderson
City: Clearwater
State: Florida
Zip/Postal Code: 33755
Country: United States
Impressive indeed, Brad!
Excellent design.

_________________
Anderson Guitars
Clearwater,Fl. 33755


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 02, 2008 3:38 am 
Offline
Koa
Koa
User avatar

Joined: Thu Aug 25, 2005 4:49 pm
Posts: 1209
Location: Ukiah, CA
It is better than Taylor's. I think this is what they were shooting for
originally. Maybe they'll steal yours.

_________________
Ken Franklin
clumsy yet persistent
https://www.kenfranklinukulele.com


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 02, 2008 5:31 am 
Offline
Contributing Member
Contributing Member

Joined: Mon Jan 03, 2005 7:46 am
Posts: 1315
Location: Branson, MO
First name: stan
Last Name: thomison
City: branson
State: mo
Zip/Postal Code: 65616
Country: united states
Focus: Build
Status: Professional
Brad first the circle cutter/rosette thing and now this. I envy you to have ability to look at something and then design and build things like that, particularly this rig. Outstanding


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 24 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 23 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com