Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 11:23 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 16 posts ] 
Author Message
 Post subject: fret re-install
PostPosted: Sat Sep 15, 2018 1:29 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
Fretted a board and had a half dozen that were not well seated. Took them all out, leveled the board again, and checked the slots, and am ready to re-install. Before I took then out, I filed the ends even with the binding on this bound board, then bevelled just a touch.

Is there a good way to get these frets back into their slots so I don't end up with a short and and a long end?

Thanks

Ed



These users thanked the author Ruby50 for the post: Bri (Sun Sep 16, 2018 10:08 am)
Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 3:42 pm 
Offline
Contributing Member
Contributing Member

Joined: Sat Aug 27, 2011 1:59 pm
Posts: 374
First name: Ken
Last Name: Lewis
City: Mt. Pearl
State: NL
Country: Canada
Focus: Build
Status: Amateur
I"m no repair guru but my instinct tells me I probably would ditch the removed frets and replace them with slightly longer ones.
The little extra could then be filed flush to the others with no worries. Wonder what the repair folk think:)


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 3:46 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
At worst, I would move them up the board to the next position that was slightly shorter, then replace the longest - #19 in this case. But I have seen a couple of builders who cut the lengths and round the ends before installing, so there must be a way.

Ed


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 3:53 pm 
Offline
Contributing Member
Contributing Member

Joined: Sat Aug 27, 2011 1:59 pm
Posts: 374
First name: Ken
Last Name: Lewis
City: Mt. Pearl
State: NL
Country: Canada
Focus: Build
Status: Amateur
Gotcha, I'm not much help then. I do think you're right tho, "there must be a way." I'll stay tuned right here
for the answer.


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 4:48 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sun Mar 30, 2008 8:20 am
Posts: 5924
When I have a fret pop loose after filing the ends I just place it back in the slot and let the "barbs" position it and tell me if I have it the right way around. If it is the wrong way around the fret will usually be noticeably off one side and the other.


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 5:02 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jan 22, 2010 9:59 pm
Posts: 3552
First name: Dennis
Last Name: Kincheloe
City: Kansas City
State: MO
Country: USA
Focus: Build
Status: Amateur
Ruby50 wrote:
At worst, I would move them up the board to the next position that was slightly shorter, then replace the longest - #19 in this case. But I have seen a couple of builders who cut the lengths and round the ends before installing, so there must be a way.

Ed

I am one of those builders, and there's no trick to it. Just put the fret where you want it and hammer it in.

The barb scars in the slot can cause trouble if the barbs are very close to them, and want to realign to the old grooves. Although in your case, it might help you get them back exactly where they were originally. You can also turn the fret around, and usually the barbs will be aligned differently relative to the old grooves in the wood.


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 6:11 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
Hadn't thought of the barb groove theory - I'll give it a try

Thanks

Ed


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sat Sep 15, 2018 11:25 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3289
Location: Alexandria MN
I’d use new freshly radiused fret wire and use hide glue injected into the slot with a syringe and needle. The bottled Stuff is fine for frets.

Do you know why they were high?

_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.



These users thanked the author Terence Kennedy for the post: dpetrzelka (Sun Sep 16, 2018 10:25 am)
Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sun Sep 16, 2018 6:29 am 
Offline
Contributing Member
Contributing Member

Joined: Sat Feb 19, 2011 7:44 pm
Posts: 1225
Location: Andersonville
State: Tennessee
Country: USA
Focus: Build
Status: Professional
If you can re-radius the pulled frets, you may be able to reinstall. I would use new fretwire.


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sun Sep 16, 2018 6:51 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Mon Jan 28, 2008 5:21 am
Posts: 4839
Location: Central PA
First name: john
Last Name: hall
City: Hegins
State: pa
Zip/Postal Code: 17938
Country: usa
Focus: Build
Status: Professional
there comes a point where saving a penny may cost a dollar use new frets
I break the corner of the fret slot with a file then spray with water , allow a few minutes then use glue as a filler and lube it helps the barbs slip in and seat.

_________________
John Hall
blues creek guitars
Authorized CF Martin Repair
Co President of ASIA
You Don't know what you don't know until you know it


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sun Sep 16, 2018 7:31 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
Thanks all

I installed an abalone strip down each side, then binding. I re-cut the slots after the abalone and unintentionally made them a little wide. I used Old Brown Glue (liquid hide) and I did not clamp long enough. I went blithely on my way down the fretboard and didn't notice that some had popped up. Look here and back one:

https://www.flickr.com/photos/ruby1638/43000477871/in/album-72157688488198220/

Ed


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Sun Sep 16, 2018 8:33 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2011 6:08 pm
Posts: 2712
First name: ernest
Last Name: kleinman
City: lee's summit
State: mo
Zip/Postal Code: 64081
Country: usa
Focus: Build
Status: Professional
Ed, FWIW ,I use fish glue to lube, and a diamond triangular file from HF to create a slight bevelled opening for the fret to seat. I use a plastic hammer fromHF to secure the fret and then use a radioused caul from stew mac in an arbor press for the final press inn . I use a machinests 45 -90 machined gauge to check for flatness on at least 3 frets, I double check when finished with a moore and wright or other suitable machinests straightedge. I find the worst offenders for proper seating of frets is the uber thin frets used on mandos ukes and dulcimers , they are a total PITA and frequently resist seating properly especially in very hdwds like ebony . Hope it works !!!


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Mon Sep 17, 2018 6:29 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Mon Jan 28, 2008 5:21 am
Posts: 4839
Location: Central PA
First name: john
Last Name: hall
City: Hegins
State: pa
Zip/Postal Code: 17938
Country: usa
Focus: Build
Status: Professional
when working with pearl on the fretboard I use CA or tite bond with ebony. Prefer the ca

_________________
John Hall
blues creek guitars
Authorized CF Martin Repair
Co President of ASIA
You Don't know what you don't know until you know it


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Mon Sep 17, 2018 10:29 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
John

My daughter recommended medium density CA and that is what I am using. Her observations is that it is pressure that kicks the glue, so it will sit in liquid state in the slot until you install in the fret. I use a polished cobbler's hammer and they are seating very nicely but I have been clamping a curved caul on them for a couple of hours TO BE SURE, even though she suggested 5 minutes would be enough.

Thanks all - It's only a mistake if you can't fix it

Ed


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Mon Oct 01, 2018 10:35 am 
Offline
Cocobolo
Cocobolo

Joined: Thu Oct 27, 2011 11:28 am
Posts: 183
First name: Leonard
Last Name: Duke
City: Kalamazoo
State: MI
Zip/Postal Code: 49001
Country: USA
Focus: Repair
Status: Amateur
I used to crank out three guitars a day in a factory warranty shop: pull the frets, make the board flat, tap the frets back in, just enough fret work to fix any buzzing frets and make it look good. It never seemed to be a problem getting the frets centered. As I recall, I started at one end of the fret and didn't proceed unless that end was perfect.


Top
 Profile  
 
 Post subject: Re: fret re-install
PostPosted: Mon Oct 01, 2018 5:10 pm 
Offline
Koa
Koa
User avatar

Joined: Sat Jan 19, 2013 7:33 am
Posts: 1831
First name: Willard
Last Name: Guthrie
City: Cumberland
State: Maryland 21502
Zip/Postal Code: 21502
Country: United State
Focus: Repair
Status: Semi-pro
On refrets where the 13th or 15th fret will be pulled for neck removal and reset after the neck is on, we do exactly as we do to mark the ends of nuts, saddles, or other easily reversed components...we use a Sharpie to put a dot on the treble end (on top of fret; underside of nut or saddle, etc.). If a 'memory jogger' mark was not applied, it is easy enough to do as other suggested and dry-fit to determine how the fret must have come out.

_________________
We have become a civilization that elevates idiots, prostitutes, and clowns. Am I still to defend it? Yes, for its principles. Yes, for what it was. Yes, for what it still may be.

-Mark Helprin, The Oceans and the Stars: A Sea Story, A War Story, A Love Story (A Novel)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: Marc, Melt in the Sun, wbergman and 43 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com