Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 3:47 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: radiusing fingerboard
PostPosted: Fri Mar 16, 2018 10:28 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jan 11, 2013 2:26 pm
Posts: 455
First name: Carl
Last Name: Dickinson
City: Forest Ranch
State: California
Zip/Postal Code: 95942
Country: USA
Focus: Build
Status: Amateur
There was a recent thread about radiusing fingerboards. DZSmith mentioned using an air sander (inline) to do it. Here's a pic of what I put together. I've had this sander since the '70s (made waterbed frames then). Velcro, 16" radius block, manzanita fretboard ... 10 minutes.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Sat Mar 17, 2018 12:21 am 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Apr 13, 2007 12:52 am
Posts: 285
Location: Canada
First name: Cal
Last Name: Maier
City: Crossfield
State: AB
Country: Canada
Focus: Build
Status: Professional
Is it level? I'm not sure I would trust a short radius block to that task.
Just sayin.

Cal

_________________
Remember, there are no stupid questions, only stupid answers!


Top
 Profile  
 
PostPosted: Sat Mar 17, 2018 8:05 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sun Mar 30, 2008 8:20 am
Posts: 5924
I've used a short block to get the general shape and then drawn pencil lines across the fretboard, and using a two foot level with sandpaper glued to the face of it, sanded along the string paths to make sure there weren't any dips in the board.

What did you use to stick the wood block to the sander?


Top
 Profile  
 
PostPosted: Sat Mar 17, 2018 1:24 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jan 11, 2013 2:26 pm
Posts: 455
First name: Carl
Last Name: Dickinson
City: Forest Ranch
State: California
Zip/Postal Code: 95942
Country: USA
Focus: Build
Status: Amateur
Before I started sanding I had a white line down the center and lots of crosshatches so felt pretty comfortable that it was sanding evenly but I will get a set of longer blocks. I think if you swapped out blocks while doing this a compound radius could be done.
Clay, I used a piece of 2 piece Velcro that was the size of the block so swapping out blocks would be easy.



These users thanked the author CarlD for the post: Clay S. (Sat Mar 17, 2018 1:37 pm)
Top
 Profile  
 
PostPosted: Sat Mar 17, 2018 3:01 pm 
Online
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Aug 19, 2005 4:02 am
Posts: 3227
Location: The Woodlands, Texas
First name: Barry
Last Name: Daniels
Drawing lines and crosshatches will not ensure a straight fretboard. Like Clay, I also use a 24" long sanding caul.

But, I use a similar setup to your sanding machine to smooth and straighten the back of a neck. My tool is an electric pad sander with a 10" flat sanding plane screwed to the bottom. It does a quick and good job of it.


Top
 Profile  
 
PostPosted: Sat Mar 17, 2018 7:32 pm 
Online
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Aug 19, 2005 4:02 am
Posts: 3227
Location: The Woodlands, Texas
First name: Barry
Last Name: Daniels
I had a request to post of photo of my back-of-the-neck sander. The sanding beam is 10.5" long and I use 100 grit paper on it. It is attached to the sander with 4 screws. The aluminum sanding beam came from a hobby store for sanding model airplane wing spars.

I use the sander in a shoe polish motion on the back of a neck to smooth out the shape after using a rasp. It leaves a surprisingly smooth surface that only needs light sanding. It also evens the neck shape nicely.


You do not have the required permissions to view the files attached to this post.



These users thanked the author Barry Daniels for the post: Pmaj7 (Sun Mar 18, 2018 11:21 pm)
Top
 Profile  
 
PostPosted: Sat Mar 17, 2018 9:50 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Carl
I like it. With the cautions you are taking to keep it from cupping, I bet it is coming out pretty darn good. As you know you can always double check with a straight edge.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Mon Mar 19, 2018 12:02 am 
Offline
Koa
Koa

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 951
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur
Yesterday I had reason (verifying neck angle on a build project) to revisit my fingerboard shaping and I clamped the fingerboard to my granite surface plate that I finally assembled and put into the wood shop. The things you find when you think you're done with a part and go for 'one more look'. The surface plate wasn't set up when I shaped that fingerboard.

I think getting the fretboard onto a dead-flat surface before sanding/shaping will pay me dividends when I get everything all glued up and fretted.

_________________
Peter Havriluk


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: Mike Thomas, rbuddy, Terence Kennedy and 47 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com