Official Luthiers Forum!
http://www.luthiersforum.com/forum/

Source for threaded inserts...
http://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=49940
Page 1 of 2

Author:  meddlingfool [ Mon Nov 13, 2017 1:42 pm ]
Post subject:  Source for threaded inserts...

I've run out of the steel neck inserts I like, and so has McFeelys. I'm on a backorder list but they've been OOS for about a month so far, no idea when they'll get more in.

I really hate the brass ones with the slit on top but will resort to those again if I must, but I would like to find some of the hard steel ones with a hex head driver.

McFadden's isn't accepting new accounts, and anything on Amazon that looks temporarily acceptable seems to be in the 7-18$ range...each!

Can anyone point me in the right direction?

Author:  Michaeldc [ Mon Nov 13, 2017 1:48 pm ]
Post subject:  Re: Source for threaded inserts...

Do any of these look right?

https://shop.stafast.com/threaded-inser ... d/screw-in

Author:  Mark Fogleman [ Mon Nov 13, 2017 1:50 pm ]
Post subject:  Re: Source for threaded inserts...

Lee Valley has a large selection and is where I get mine from. Your local hardware store will probably have them also.

Author:  jfmckenna [ Mon Nov 13, 2017 2:22 pm ]
Post subject:  Re: Source for threaded inserts...

I just go down to my local Home Depot. In fact I'll be stopping there on my way home tonight.

Author:  meddlingfool [ Mon Nov 13, 2017 2:39 pm ]
Post subject:  Re: Source for threaded inserts...

Hey, yeah, the Stafast SK are the ones. Lee Valley and HD only carry the brass ones which I don't like...

Thanks!

Author:  meddlingfool [ Mon Nov 13, 2017 2:51 pm ]
Post subject:  Re: Source for threaded inserts...

Of course they're out of stock duh

Author:  Dan Miller [ Mon Nov 13, 2017 2:55 pm ]
Post subject:  Re: Source for threaded inserts...

I always say "if you can't get it from McMaster, they don't make it"

https://www.mcmaster.com/#threaded-inse ... 75j9ylw4tc

Plus, shipping can be so fast that it seems like they sent your order before you placed it. Cost of shipping has always been reasonable from McMaster for me.

Author:  meddlingfool [ Mon Nov 13, 2017 2:59 pm ]
Post subject:  Re: Source for threaded inserts...

Ill try McMaster s again, but last time I did they were not accepting new accounts..l

Author:  Michaeldc [ Mon Nov 13, 2017 3:44 pm ]
Post subject:  Re: Source for threaded inserts...

meddlingfool wrote:
Hey, yeah, the Stafast SK are the ones. Lee Valley and HD only carry the brass ones which I don't like...

Thanks!



Bummer!!

Author:  Tim Mullin [ Mon Nov 13, 2017 4:17 pm ]
Post subject:  Re: Source for threaded inserts...

meddlingfool wrote:
Hey, yeah, the Stafast SK are the ones. Lee Valley and HD only carry the brass ones which I don't like...!

Ed, have a look at this Canadian site:
https://www.globalindustrial.ca/g/fasteners/Threaded-Inserts/thread-inserts-for-wood/E-Z-Lok-Die-Cast-Zinc-Alloy-Hexdrive
I was looking here for some other stuff, but remembered seeing what appeared to be a large assortment of threaded inserts.


Sent from my iPad using Tapatalk

Author:  meddlingfool [ Mon Nov 13, 2017 4:23 pm ]
Post subject:  Re: Source for threaded inserts...

Thanks Tim,

Unfortunately those are not the right kind...

Author:  Tim Mullin [ Mon Nov 13, 2017 4:30 pm ]
Post subject:  Re: Source for threaded inserts...

meddlingfool wrote:
Thanks Tim,

Unfortunately those are not the right kind...

Pity — that site is the most diverse of any fastener supplier I’ve come across in Canada.
We’ll be keen to know how you finally source these.


Sent from my iPad using Tapatalk

Author:  meddlingfool [ Mon Nov 13, 2017 5:13 pm ]
Post subject:  Re: Source for threaded inserts...

They kind I like are hex insert hard steel. They had hex head zinkmfor soft wood, and slot top hard steel, so not quite right.

Happily, however, McMasters was indeed open to taking an order, which took all of 5 minutes by phone, and they even cover the brokerage, so Yahtzee!

Thanks, folks:)

Author:  mountain whimsy [ Mon Nov 13, 2017 5:53 pm ]
Post subject:  Re: Source for threaded inserts...

What size inserts are you all using? Thinking about going this way, too.

Author:  meddlingfool [ Mon Nov 13, 2017 7:12 pm ]
Post subject:  Re: Source for threaded inserts...

I'm using first down under steel...Image

Author:  SnowManSnow [ Mon Nov 13, 2017 7:23 pm ]
Post subject:  Re: Source for threaded inserts...

meddlingfool wrote:
I've run out of the steel neck inserts I like, and so has McFeelys. I'm on a backorder list but they've been OOS for about a month so far, no idea when they'll get more in.

I really hate the brass ones with the slit on top but will resort to those again if I must, but I would like to find some of the hard steel ones with a hex head driver.

McFadden's isn't accepting new accounts, and anything on Amazon that looks temporarily acceptable seems to be in the 7-18$ range...each!

Can anyone point me in the right direction?

Try a company named fastenall. They have nearly every type of fastener you can think of. (Now watch... they won’t have the one you need)


Sent from my iPhone using Tapatalk Pro

Author:  meddlingfool [ Mon Nov 13, 2017 9:07 pm ]
Post subject:  Re: Source for threaded inserts...

They don't...:)

Author:  Bri [ Mon Nov 13, 2017 9:48 pm ]
Post subject:  Re: Source for threaded inserts...

Stafast products Canadain Mississauga

Author:  meddlingfool [ Tue Nov 14, 2017 12:23 am ]
Post subject:  Re: Source for threaded inserts...

Stafast out of stock...

Author:  Matthew Jenkins [ Tue Nov 14, 2017 1:46 am ]
Post subject:  Re: Source for threaded inserts...

I got my last batch from 'Rockler'.

Author:  Matthew Jenkins [ Tue Nov 14, 2017 1:46 am ]
Post subject:  Re: Source for threaded inserts...

I got my last batch from 'Rockler'.

Author:  Clay S. [ Tue Nov 14, 2017 11:57 am ]
Post subject:  Re: Source for threaded inserts...

I prefer the zinc inserts with the broken thread. I think the bite a little deeper into relatively soft hardwoods like walnut and mahogany.

Author:  Mark Mc [ Tue Nov 14, 2017 2:03 pm ]
Post subject:  Re: Source for threaded inserts...

Stepping back from the choice of which threaded insert..........my question would be why use threaded inserts? I have had problems of them stripping out of the end-grain in the neck, as have other people. Perhaps your hardware or technique are better than mine, but it just seems like a sub-optimal method to me. I use barrel bolts inserted in a hole drilled up from the heel. Even stronger is the method described in the Gore/Gilet books. They cut a square channel up from the heel and inserting a square-profile brass tube, into which there are threaded holes for the bolts. That method seems completely bullet-proof, but I am not tooled up to cut the square hole.

Author:  meddlingfool [ Tue Nov 14, 2017 2:16 pm ]
Post subject:  Re: Source for threaded inserts...

Clay S. wrote:
I prefer the zinc inserts with the broken thread. I think the bite a little deeper into relatively soft hardwoods like walnut and mahogany.


I want the bolts to be a softer material than the inserts. If, in the unlikely circumstance either needs to be replaced, I want it to be the bolt, which can simply be replaced, rather than the insert, the replacement of which would be quite the chore...

Author:  meddlingfool [ Tue Nov 14, 2017 2:28 pm ]
Post subject:  Re: Source for threaded inserts...

Mark Mc wrote:
Stepping back from the choice of which threaded insert..........my question would be why use threaded inserts? I have had problems of them stripping out of the end-grain in the neck, as have other people. Perhaps your hardware or technique are better than mine, but it just seems like a sub-optimal method to me. I use barrel bolts inserted in a hole drilled up from the heel. Even stronger is the method described in the Gore/Gilet books. They cut a square channel up from the heel and inserting a square-profile brass tube, into which there are threaded holes for the bolts. That method seems completely bullet-proof, but I am not tooled up to cut the square hole.


Because if you get the right threaded insert your problems with them more or less disappear.

I'm not too concerned with 'stronger', it only needs to be 'enough' strong to hold the neck immobile under string tension.

Definitely the G/G method is the best, but, at 1599 base, not really practical for me.

If you're worried about the inserts stripping the endgrain, you can drive a 3/4" dowel up through the heel and put the inserts into that, which I have done in the past both as a preventive object in soft Spanish cedar, and as a restorative effort in same. In Khaya, my main neck wood these days, it simply isn't a problem.

Having gone from dovetail, to M&T, to double M&T, to bolt on butt joint with glued tongue, I don't find the last system subpar by any means at all. I had first considered it that myself, and had intended only to use it on my budget line, but once I saw how excellently it works, it's now my only neck joint.

When my base price for the fancy stuff is 5k$, I'll consider moving to the 'better' method in the G/G books, but even then not so much because I think the extra work yields a practical payoff, but so I can point to it as part of why it's 5k$.

Page 1 of 2 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/