Official Luthiers Forum!
http://www.luthiersforum.com/forum/

Build 4 1/2
http://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=49841
Page 1 of 2

Author:  SnowManSnow [ Sat Oct 21, 2017 9:23 pm ]
Post subject:  Build 4 1/2

Well this is build 4 1/2
It is 4 1/2 because build 4 was halted because of a foolish critical error.

My thought here is a responsive OM geared toward finger style w a 1 7/8 nut. It is maple and spruce with ebony binding.
The rosette is very mild with 2 contrasting maples surrounded by bwb (the same as will be on the top and back purfling.

Image
Image
Image

Will post pics as I progress (or screw up whichever comes first haha)
Peace
B



Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Sat Oct 21, 2017 9:56 pm ]
Post subject:  Re: Build 4 1/2

Carving some back braces!
Image


Sent from my iPhone using Tapatalk Pro

Author:  J De Rocher [ Sat Oct 21, 2017 10:15 pm ]
Post subject:  Re: Build 4 1/2

Off to a good start. It'll be cool to see the rosette under finish.

Author:  SnowManSnow [ Sat Oct 21, 2017 10:21 pm ]
Post subject:  Re: Build 4 1/2

J De Rocher wrote:
Off to a good start. It'll be cool to see the rosette under finish.

I’m hoping it isn’t too mild. Normally I like a little more contrast w the top.



Sent from my iPhone using Tapatalk Pro

Author:  Joe Beaver [ Sun Oct 22, 2017 12:42 am ]
Post subject:  Re: Build 4 1/2

I think it is going to a nice looking build. What are your thoughts on binding?

Author:  Hesh [ Sun Oct 22, 2017 5:26 am ]
Post subject:  Re: Build 4 1/2

Looking great Snow!

I always loved carving braces and found it to be very relaxing.

Author:  SnowManSnow [ Sun Oct 22, 2017 10:18 am ]
Post subject:  Re: Build 4 1/2

Joe Beaver wrote:
I think it is going to a nice looking build. What are your thoughts on binding?

Ebony


Sent from my iPhone using Tapatalk Pro

Author:  truckjohn [ Sun Oct 22, 2017 12:02 pm ]
Post subject:  Re: Build 4 1/2

Very nice. I understand the dilemma about having to jettison a build. I had to do that myself earlier this year. It just kept going from bad to worse. At some point - you have to cut the rope.

Author:  SnowManSnow [ Sun Oct 22, 2017 1:00 pm ]
Post subject:  Re: Build 4 1/2

Image
A few extra hours on this Sunday ;)


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Sun Oct 22, 2017 1:16 pm ]
Post subject:  Re: Build 4 1/2

:)
Image
1/8 “ at the edges


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Sun Oct 22, 2017 1:39 pm ]
Post subject:  Re: Build 4 1/2

Image
Picture break between hand cramps w this tiny plane


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Sun Oct 22, 2017 2:02 pm ]
Post subject:  Re: Build 4 1/2

Back braces:)
Image


Sent from my iPhone using Tapatalk Pro

Author:  Clay S. [ Sun Oct 22, 2017 7:29 pm ]
Post subject:  Re: Build 4 1/2

"Joe Beaver wrote:
I think it is going to a nice looking build. What are your thoughts on binding?"

SnowManSnow replied:
"Ebony "

The beauty of ebony binding is, that if well done, it looks just like black plastic! beehive

I did a guitar in ebony once. Now I use black plastic. It doesn't have the coolness factor but it is a lot easier to install, and a bit tougher.

Author:  SnowManSnow [ Sun Oct 22, 2017 8:48 pm ]
Post subject:  Re: Build 4 1/2

Looks a lot like plastic:) I like it bc it’s hard as crap. And it’s ... not plastic/)


Sent from my iPhone using Tapatalk Pro

Author:  Clay S. [ Mon Oct 23, 2017 10:19 am ]
Post subject:  Re: Build 4 1/2

If you use black ebony for binding you can install it in two 1/2 thickness pieces. It makes bending it so much easier! When it is sanded and finished the glue line is unnoticeable.

Author:  SnowManSnow [ Mon Oct 23, 2017 2:11 pm ]
Post subject:  Re: Build 4 1/2

Clay S. wrote:
If you use black ebony for binding you can install it in two 1/2 thickness pieces. It makes bending it so much easier! When it is sanded and finished the glue line is unnoticeable.

Already have it all bent:) ready to go.
That said I may use it to r go w something :) no worries


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Sat Oct 28, 2017 6:12 pm ]
Post subject:  Re: Build 4 1/2

Image

Whew


Sent from my iPhone using Tapatalk Pro

Author:  Haans [ Sat Oct 28, 2017 8:05 pm ]
Post subject:  Re: Build 4 1/2

Just a tip Snow Man, next time don't notch the braces, notch the center strip...
Lots of folks don't care much for the popsicle stick on the top, but it works well.
Hope it all works out for you!

Author:  SnowManSnow [ Sat Nov 04, 2017 6:48 pm ]
Post subject:  Re: Build 4 1/2

Here are a few updates. I... again.... had a few major issues, however I managed to repair my own issues and won’t mention them in detail.
I got the binding and purfling installed, a few gaps filled and the top and back sanded. The sides still need a little tlc w some paper.
Image
Image
Image
Image
Image


Sent from my iPhone using Tapatalk Pro

Author:  Clay S. [ Sat Nov 04, 2017 7:41 pm ]
Post subject:  Re: Build 4 1/2

Looking Good!

Author:  Hesh [ Sun Nov 05, 2017 12:42 am ]
Post subject:  Re: Build 4 1/2

Looks great!!

Author:  SnowManSnow [ Mon Nov 13, 2017 7:46 pm ]
Post subject:  Re: Build 4 1/2

Image
Getting this shaped in.
By the way guys... these dragon rasps from stewmac are serious cutters! Good stuff


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Wed Nov 15, 2017 10:31 pm ]
Post subject:  Re: Build 4 1/2

Lines on the neck
Image
Image


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Thu Nov 16, 2017 5:25 pm ]
Post subject:  Re: Build 4 1/2

Heel block now rough shaped.
Image
Liking the curves here:) it’s my first carved neck:) haven’t botched it yet..... not........ yet:)


Sent from my iPhone using Tapatalk Pro

Author:  SnowManSnow [ Thu Nov 16, 2017 5:25 pm ]
Post subject:  Re: Build 4 1/2

Tenon is next:)


Sent from my iPhone using Tapatalk Pro

Page 1 of 2 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/