Official Luthiers Forum!
http://www.luthiersforum.com/forum/

13 fret L00
http://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=44623
Page 1 of 1

Author:  Derek [ Sat Nov 22, 2014 5:05 pm ]
Post subject:  13 fret L00

Just finished 13 fret L00
Yellow Cedar/English Walnut

Attachment:
photo 1.jpg


Attachment:
photo 2.jpg


Attachment:
photo 4.jpg


Attachment:
photo 3.jpg

Author:  sdsollod [ Sat Nov 22, 2014 5:24 pm ]
Post subject:  Re: 13 fret L00

Very Nice! I like the rosette.

Author:  Colin North [ Sat Nov 22, 2014 5:28 pm ]
Post subject:  Re: 13 fret L00

Nice one Derek, looks like tortoiseshell bindings?
What wood is the neck? Looks figured (I'm assuming its not pawprints!)

Author:  jack [ Sat Nov 22, 2014 5:55 pm ]
Post subject:  Re: 13 fret L00

looks nice!

Author:  Chris Pile [ Sat Nov 22, 2014 6:58 pm ]
Post subject:  Re: 13 fret L00

Well done!

Author:  meddlingfool [ Sat Nov 22, 2014 8:36 pm ]
Post subject:  Re: 13 fret L00

Love NL oo's!

Author:  cphanna [ Sun Nov 23, 2014 11:27 am ]
Post subject:  Re: 13 fret L00

Clean, elegant, understated...with just the right amount sparkle in that rosette. I think it's quite beautiful.

Author:  Tim L [ Sun Nov 23, 2014 1:11 pm ]
Post subject:  Re: 13 fret L00

Nice clean looking guitar. How does that wood combo sound?

Author:  Pmaj7 [ Sun Nov 23, 2014 5:37 pm ]
Post subject:  Re: 13 fret L00

Nice looker!

How big is the sound hole? Your logo looks a little pixilated. Maybe use a higher resolution camera?

Author:  George L [ Sun Nov 23, 2014 8:17 pm ]
Post subject:  Re: 13 fret L00

Yeah, I like it! Unusual materials and a very imaginative aesthetic. Good job!

Author:  James W B [ Mon Nov 24, 2014 10:17 am ]
Post subject:  Re: 13 fret L00

I'll bet moving the bridge back a bit gives you a bigger sound than a 14 fret.Ive always liked 12 frets for this reason but a little short.13 sounds like a good compromise

Author:  Derek [ Tue Nov 25, 2014 3:11 am ]
Post subject:  Re: 13 fret L00

Thanks for the kind comments!
This was had been lying around for a while needing re-topped. Unfortunately when routing off the bindings the router bit somehow slipped and I took more off at the neck block. This resulted in a slope from soundhole to neck, allowing me to make a sort of cantilevered neck! Which has come out well with a nice low action as a consequence:
Attachment:
20141124_122100.jpg


Neck is an old brazilian hog shelf which has some figure
Attachment:
20141124_122100.jpg


Bindings are rosewood. I am very pleased with the sound and will definitely use the wood combination again.
Apologies for the poor pictures. Will also try to add a video at some point.
Attachment:
20141124_121957.jpg

Attachment:
20141124_122328.jpg

Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/