I agree with Trevor.
Bob
| Official Luthiers Forum! http://www.luthiersforum.com/forum/ |
|
| Where to get a press screw... http://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=44537 |
Page 1 of 1 |
| Author: | sdsollod [ Mon Nov 10, 2014 11:59 am ] |
| Post subject: | Where to get a press screw... |
I need a press screw for a cutaway attachment for my bender. I bought one a few years ago for my home made bender but I don't remember where I got it. Seems like there aren't that many places that have them. I found one online at Woodworker's Supply. Are there any other suggestions on where I could find one? Woodcraft - no... Klingpuors -no, Home Depot - no, Lowes - no, hardware store - no, Rockler - no, Highland Wood Working - no, Joe Wood Worker - no, Lee Valley - no (only in Canada)... |
|
| Author: | Bri [ Mon Nov 10, 2014 12:05 pm ] |
| Post subject: | Re: Where to get a press screw... |
Grizzly tools, around $15 if I remember correctly. B |
|
| Author: | Jim Watts [ Mon Nov 10, 2014 12:13 pm ] |
| Post subject: | Re: Where to get a press screw... |
McMaster-Carr has them too. |
|
| Author: | Heath Blair [ Mon Nov 10, 2014 12:31 pm ] |
| Post subject: | Re: Where to get a press screw... |
http://www.grizzly.com/products/Veneer-Press-Clamp/D2893 As mentioned. |
|
| Author: | Joe Beaver [ Mon Nov 10, 2014 12:54 pm ] |
| Post subject: | Re: Where to get a press screw... |
I got mine from good old LMI |
|
| Author: | Tom West [ Mon Nov 10, 2014 1:51 pm ] |
| Post subject: | Re: Where to get a press screw... |
I think Lee Valley may also have them. Tom |
|
| Author: | Greg [ Mon Nov 10, 2014 2:26 pm ] |
| Post subject: | Re: Where to get a press screw... |
Can you show a picture of the cutaway bending attachment? Looking to add to my bender. |
|
| Author: | TonyKarol [ Mon Nov 10, 2014 4:51 pm ] |
| Post subject: | Re: Where to get a press screw... |
I just bought one today at Lee Valley .. in Canada ... |
|
| Author: | Trevor Gore [ Mon Nov 10, 2014 5:20 pm ] |
| Post subject: | Re: Where to get a press screw... |
16mm (5/8") threaded rod is fine for the duty it will see. Has worked fine on my double side bender for the last 15 years or so and will last at least that long again. |
|
| Author: | John Killin [ Mon Nov 10, 2014 5:34 pm ] |
| Post subject: | Re: Where to get a press screw... |
I got mine from McMaster Carr. http://www.mcmaster.com/#press-screws/=ujes8r |
|
| Author: | kwerry [ Mon Nov 10, 2014 5:39 pm ] |
| Post subject: | Re: Where to get a press screw... |
Amazon http://www.amazon.com/Shop-Fox-D2893-Pr ... grid_i_0_0 KLW |
|
| Author: | unkabob [ Mon Nov 10, 2014 9:23 pm ] |
| Post subject: | Re: Where to get a press screw... |
I agree with Trevor. Bob
|
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|