+2 for curly koa.... Am biased though as this was my first build
Macassar with koa bindings
| Official Luthiers Forum! http://www.luthiersforum.com/forum/ |
|
| Binding choice for Macassar Ebony B&S http://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=41398 |
Page 1 of 1 |
| Author: | Jim Kirby [ Sat Sep 14, 2013 2:34 pm ] |
| Post subject: | Binding choice for Macassar Ebony B&S |
I've been using cocobola bindings on my rosewood guitars (classical, with w/b/w mitred purflings on sides, back, end strip and back strips). I'm starting my first using Macassar Ebony (with cedar top) and I'm up in the air about binding choice. I'm afraid the slightly green/tan hue of the ebony together with the reddish hue of the cocobola will look like a Christmas ornament. Does the sort-of greenish hue of the Ebony stay that way under finish? (I know, I need to do some testing.) What have you used in the past? Not looking for a lot of contrast in the bindings. I could always self-bind, but looking for a little something extra. |
|
| Author: | Rod True [ Sat Sep 14, 2013 2:57 pm ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
I'd rather stick with off cuts of the sides for that classy tuxedo look or I'd go with curly koa or similar. |
|
| Author: | DennisK [ Sat Sep 14, 2013 3:14 pm ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
How about pau ferro? Or black ebony. Or walnut. Maybe curly? |
|
| Author: | Frank Cousins [ Sat Sep 14, 2013 3:37 pm ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
+2 for curly koa.... Am biased though as this was my first build Macassar with koa bindings
|
|
| Author: | Jim Kirby [ Sat Sep 14, 2013 4:32 pm ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
Frank Cousins wrote: +2 for curly koa.... Am biased though as this was my first build Macassar with koa bindings That's pretty indeed, but not what I'm after for the stately, low-key, de riguer classical look. Although, the ebony looks like it warms up enough under finish that my original concern may be moot. Time to test! |
|
| Author: | Rod True [ Sat Sep 14, 2013 5:17 pm ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
I'd go with off cuts than..... |
|
| Author: | Joe Beaver [ Sun Sep 15, 2013 1:58 am ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
Franks curly koa looks very sharp, but then the macassar he used is on the none typical side of outstanding. Have to see your sides but I would go with something dark, gaboon ebony or dark indian rosewood or BRW if you can find it |
|
| Author: | Jim Kirby [ Sun Sep 15, 2013 7:35 am ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
My set tends more towards Frank's rather than Filippo's. I looked at it under naptha last night and I think it may well warm up enough under finish to not cause the problem I was worried about. The snakewood is nice. Any of that lurking around anywhere? |
|
| Author: | Frank Cousins [ Sun Sep 15, 2013 7:54 am ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
Jim Kirby wrote: My set tends more towards Frank's rather than Filippo's. I looked at it under naptha last night and I think it may well warm up enough under finish to not cause the problem I was worried about. The snakewood is nice. Any of that lurking around anywhere? Good find! I was so lucky when I just found that set in 2007 - for only £160 which was the around $200 - slight flame on the back as well and have not seen anything close since - with even very average wood being in excess of £280 Snakeroot would be great IMHO, but again tricky to find... The Koa binding was from Bobc, not sure if he has any left with that tight curl, but saw he has some figured mahogany that could work. Must admit, using side cut offs with say a 0.3mm pear or maple 'coach' lining would look early classy on a classical |
|
| Author: | Arnt Rian [ Mon Sep 16, 2013 4:14 am ] |
| Post subject: | Re: Binding choice for Macassar Ebony B&S |
If the wood already has a lot of contrast, my first choice would be side off-cuts, or something of similar or darker hue. Too much contrast, with figured, curly etc. woods can quickly make for a very busy and incoherent visual package (IMO). Generally, I think its not just a matter of which woods and colors "match", because lots of things can look great, but still not appropriate for all instrument. Its better to pick on a theme for the design concept, and chose the woods and appointments accordingly. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|